I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hey Nordic team ,
We are trying to work on use-case where we want NRF52840 to generate thread Stack message but instead of using multi-protocol features it can transmit...
Hi,
I know nrf52840 does not support direction finding and it seems because of hw limitation like the link.
But can I get a little more detail why nrf52840 can not...
Hello all,
Currently, we are using the nRF52840-DK and realized that the interface to upload programs is very handy (being able to simply drag a .hex file onto the device...
Hi,
after updating my NCS version to v2.1.2 I noticed that my Zephyr SDK also needed updating from 0.14.1 to 0.15.1. However, after updating my Matter project does not compile...
Hello,
When using two nRF52832 modules for Bluetooth connection, can it prevent Dos attack program? We have found a situation where a malfunctioning or malicious client...
Hi,
I am evaluating the nRF5340 Audio DK and measuring while adjusting the audio bitrate.
I found the following 3 symbols definition for bitrate.
CONFIG_LC3_BITRATE...
Hello
I got a nRF52840 DK and try to use Direct Test Mode APP (v2.0.3) in the nRF Connect for Desktop (v3.12.0).
However, it always says "Can not communicate with device...
I have sdk 2.1.0 and nrf5340, trying to run peripheral_uart sample connecting nrf5340 to a module via uart. The program seems working when only works with nrf5340 based on...
Dear Nordic Support Team,
I wanted to configure the nRF52840 dongle as radio co-processor. For that I wanted to build and flash the Thread: Co-processor sample in nRF52840...
Good day
I intend to use a power saving mode to turn on a device for a set amount of time. During this, the device would still need to receive commands over mqtt. Is this...
Dear SRs
We are evaluating your NB-IoT solution by means of Thingy91 reference board. The NB-IoT service is working with iBASIS card, the question is: can we change the...
I've created the samples for Socket Echo Client https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/zephyr/samples/net/sockets/echo_client/README.html#sockets-echo...
HI , I am having difficulty in interfacing the flash with my DK board
1) The spi flash sample is getting stuck at flash erase function without any error responses
2) I...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
