Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello, I am currently working on a project where I need to be able to put the device in low power mode (PM_STATE_SOFT_OFF), but I am also using the LittleFS filesystem for...
Hello,
I would like to trigger an action on every successfull connection event of a BLE connection.
Is there a way to know when the connection event was successful or...
Hi all,
We try to compile the smallest project for NRF7002. We except to use it for scan only.
We start from the shell wifi sample in NCS 2.1.2.
When we remove the configuration...
Hello,
thank you for your help to solve my previous issue with resetting the RTC event ( ). I'm glad to move to the next problem with my task, which is triggering the SAADC...
Hello, i tried to implement a commissioner over the API, but i get the error undefined reference to `otCommissionerStart'. In the prj.conf i added:
# Enable COMMISSIONER...
Hi everybody,
I am trying my best to make my nrf52840dk communicating with an external bmp280 sensor using i2c, but I could not even read the cip id.
Maybe I completely...
Hi,
I'm currently using an nRF9160DK with an NB-IoT sim, and the problem I am currently having is that I cannot establish a connection with the nRF cloud.
What have...
Hi,
we have 10 nRF52840 DK's 8 are version 1.0.0 and 2 are version 3.0.0(purchased this week).
The older version 1.0.0(made in Norway) work perfect with our 3V boards...
Hi all, I got the nRF52833-DK 2 months ago. I've deployed the heart_rate_demo.hex example to it and it seemed to work. Now i'm trying to connect the DK to the PC again and...
Hi Everyone,
I am starting development of new project and we are using the module MBN52832.
Now I want to start my development for this board. I have a few questions...
Hello,
My questions is very simple but I found many trouble during the procedure.
I would like to export my project (created con VSCode) from my PC to antother one and...
Hello everyone!
While programming nRF52805 module, I am encountering an error in memory reading stage. Logs from the application (both Failure and success cases) are attached...
Hi, I am working on a Homekit project and the nRF Homekit SDK uses NVS settings to store data in the internal flash. Is it possible that I can add another partition in the...
Hardware:
nRF52840 DK
S140 Soft Device
SDK 15.2.0
Hello,
I want to confirm my understanding of the impact of flash operations on the nRF5240 when using the SoftDevice...
