I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello dear,
I am installing Embedded Studio on OSX (Catalina), and I following the nRF Connect step... all goes fine, but when I try to use "Open nRF Connect SDK Project...
I'm trying to see debugging info with nrf51 dongle.
As far as I can tell I just need to use:
#define NRF_LOG_MODULE_NAME "APP"
#include "nrf_log.h"
#include "nrf_log_ctrl...
On a nRF5340 DK the sample ncs/zephyr/samples/subsys/usb/cdc_acm runs fine. However, if I add "CONFIG_NO_OPTIMIZATIONS=y" to prj.conf I get faults (see below). Any ideas why...
Hi,
I am preparing Windows desktop application which will use nrfutil for DFU of the products (containing secure dfu bootloader). I tested nrfutil v6.1.0, v6.0.1 and even...
Hii guys,
I am trying to establish communication between two nrf52 module.
My application is as following
1. I need a central device which can work as master and remains...
Hello, I am stuck initalising both TWIM and UARTE. I am focusing on the TWI Scanner example but using TWIM instead of TWI. No matter what I do I cannot get past the initalisation...
Hi,
How can I increase TX Power in nRF Connect SDK ?
I have already followed the hci_pwr_ctrl example, but I got the error "Read Tx power err: -5 reason 0x00" in get_tx_power...
We use nrf connect sdk under linux.
I need to control tx power to be able to adjust working range.
I take example from zephyr/samples/bluetooth/hci_pwr_ctrl
Add segger_rtt...
Hello,
I recently cloned NCS v1.5.0-rc1 using west init -m https://github.com/nrfconnect/sdk-nrf.git followed by git checkout v1.5.0-rc1 and then west update in the nrf...
Hello,
I'm a beginner and I'm a bit lost. It's rather complex to understand everything there is to know. So I ask a lot of questions, sorry.
I was advised to use the lib...
Hello,
We are not finding RFX2401C on the market for sale and we are looking for a PA for the NRF24L01+.
We found the alternative RFX2411, is it safe to assume we can...
Dear community
I'm developing BLE secure firmware on an event-driven proprietary RTOS.
According to the documentation of nrf_ble_lesc_request_handler() , it is required...
Is the BLE connectivity offered by the nRF52840 (upon which the Arduino Nano 33 BLE is based, I think) DIRECTIONAL? Should the board be oriented in any particular way to maximize...
