Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello,
In my code, I would like to use the power_down_unused_ram () function. I included the ram_pwrdn.h file but the build returns with undefined reference to `power_down_unused_ram...
Hello. I want to the use pwm_library example for setting a PWM on a GPIO. It works well except that the initial state of the GPIO is high for about 230us before the PWM starts...
I am in the process of adding LE Secure connections to our project and am having trouble and receiving lots of errors while attempting to Makefile it. We added nrf_ble_lesc_request_handler...
Hello,
Developing an application where we want to use CAF but I cannot get it to build properly. I have created a minimal example that does not work locally for me. Following...
The nrf52840 defines 4 pwms. Attempting to enable pwm1, pwm2 or pwm3 using pinctrl through a device overlay results in build errors suggesting there is something wrong with...
Hello, we currently use nRF52832 in our product. For the next generation of this product, we are hoping to upgrade to a new module that uses nRF52833. However, this is only...
We have a well-vetted software environment what uses SDK 15.3.0 and softdevice s132. We are considering adding ANT+ to our environment, which as I understand requires that...
I am in the process of bringing up a custom board with an nrf5340 and a FUSB302B USB-C PHY-controller.
As a driver for the FUSB203B, I am using this project as an OOT-module...
Hello
Due to some reasons we need to use external antenna and RF cables.
What is a part number of the antenna that can be connected to the J1 RF Antenna connector?
We...
Hi,
I am implemented the uart functionality, I'm getting below issue.
[00:00:00.445,526] <err> Throughput: Failed to set UART callback (err -88) [00:00:00.445,556] <err...
I want to use LPCOMP in nrf52832 to detect a rising edge of voltage. And my code is:
I set the reference as NRF_LPCOMP_INPUT_1 or NRF_LPCOMP_REF_SUPPLY_4_8, the event is...
I am running on openthread demo: ot_cli on its low power mode by building with low_power snippet.
As document says, it will automatically suspend UART operation when low...
Hi,
I'm trying to use to gpio pins in order to wake up a system from sleep mode.(PIN1= P0.24 PIN2 =P1.1 )
If I use the GPIOTEs separately in my project, it works and sytem...
There are some serious issues in the file "board.c" that relate to LEDS_NUMBER.
If I create a custom board with no LEDs then I set LEDS_NUMBER to in my custom boards,h....
