Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
When I compile the attached example project like this:
I get the following warning:
And the compile flags for main.c (taken from compile_commands.json) are:
I...
Hi all !
I recently faced an weird issue with a nRF5340 (on a DK board, and then a custom PCB). When writting to the PWM peripheral, configured to some GPIO pins, some...
I am trying to run central_uart example which is failing when bt_settings_init function is called. I debugged further and found that
settings_subsys_init is called inside...
Hi all,
I need to generate two 1 MHz signals with opposite phases. However once I configure the decode mode as "Individual" I don't have output signals. In case of "Common...
Hi,
Where can I find the nRF9151 CE/RED RF test results for the purpose of CE delta certification of a new product based on nRF9151? (i.e. leveraging existing nRF9151 certification...
I am trying to configure the absolute time in my application, which at some point receives the time_t epoch value from an external source and should update it internally so...
Hi ! I have 5 different bootloaders for 5 pieces of hardware that I would like to cycle test OTA DFU with BLE. I have some questions
Why does nrfutil dfu ble require a...
Dear Nordic Team,
I've been working extensively on creating a custom sensor driver building on Zephyr's sensor API. Throughout this process, I've utilized many available...
Hi,
after having issues with my devkit flashing the main MCU, the interface MCU isn't being seen on USB anymore.
LED5 is blinking rapidly.
The board is a PCA10040...
I am creating a custom board with an W25Q128JVPIQTR external flash drive using SPI with a nrf5340. The pins are:
P0.08 - SD_CLK
P0.09 - SD_MOSI
P0.10 - SD_MISO ...
Regarding the operation of EJ2832AA1 (nRF52832), Please answer the following questions. nRF5 SDK ： v15.3.0 SoftDevice ： S132 v6.1.1
I am doing UART communication with another...
Hello, I am new here and I hope to not duplicate any other similar post (to be honest I have search a lot before writing). I am working with nrf52840DK, I have used blinky...
Hi,
Is there anyway to start after stopping the PWM with a PPI channel?
There is a start task in the PWM, but
But not defined in the nrfx pwm driver (nrf_pwm.h)
I...
We're trying to set up MQTT messaging between our custom nRF9160 device and our private AWS VPC. When using the Serial Terminal in nRF Connect for Desktop to monitor the device...
I am reaching out to request assistance regarding a FOTA (Firmware Over-The-Air) operation using the HTTPS protocol for my new nRF7002-DK development kit. I have successfully...
