I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I can't define an Advertising file larger than 191 bytes, even in Extend.
Here's my code and proj.conf file.
My board is an NRF52840.
main.c
proj.conf
E...
Hello,
I'm working through the fundamental courses and trying to get my nrf54lm20 development board setup. After I have built and flashed the sample firmware to the dev...
I just upgraded my project (that runs on custom hardware with the nRF8233 using an Ezurio BL653 module) from nRF Connect SDK v3.1.0 to SDK v3.2.1 and the battery monitoring...
Hi, we have recently started developing with the nRF5340DK. We encountered several issues while configuring a FATFS on the external flash (mx25r64).
1. The sample code...
Hello
I am currently trying to develop an asset tracker based on your Asset Tracker Template ( GitHub - nrfconnect/Asset-Tracker-Template · GitHub ). While going through...
Hi,
I am trying to configure SWO logging in a sample project based on zephyr/samples/hello_world (source and config at the end).
I run this application on two targets...
Hello,
In document nRF54L15_qfaa_4L_config1_pcb_reference_layout_0_6 there is a representation of the PCB with 4 layers. The GND of C9 is not connected on the top layer...
Hi,
When configuring an nRF54LM20A for usb and then using the `onoff_request()` API to enable the HFCLK after that, results in spinning sys_notify_fetch_result() forever...
Hi
I am currently experiencing an issue with my custom board related to poor BLE signal performance.
My devices are based on the NORA-B101 (nRF5340) combined with a SKY66408...
Enable the "mcuboot_with_encryption" function. 1: When using VSCode for flashing, by default, mcuboot is flashed with un-signed and un-encrypted firmware, while the application...
Hello team,
I wanted to implement direction finding using BT for nRF5340 available in Thingy 91x.
Please let me know is it possible to implement or any pre available examples...
Hi devzone, I'm working on the nRF54L05, having an application and the mcuboot generated correctly on my host computer. Now we want to generate the binaries on Bitbucket pipelines...
Our company is developing second-generation implantable medical devices and plans to use the nRF54LM20A chip/component. We place a high priority on product reliability, so...
HI,
I am using "NRF_POWER -> TASKS_CONSTLAT = 1 ;" to enable CONSTLAT, but when i printf("TASKS_CONSTLAT %d",NRF_POWER->CONSTLATSTAT); the result is still 0; how can i...
We are using the Asset Tracker Template with on a nRF9151-SMA-Devkit, using the enclosed external GNSS antenna outdoors (out of the window) and the GNSS reception is very...
