Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
In section 5 of 'nRF91 Series Antenna and RF Interface Guidelines' there are a couple of circuit diagrams relating to antenna tuners, could you please provide details of how...
Hi,
I just saw the announcement for PRS support. This is very interesting to us for use cases where GNSS reception is temporarily poor. Questions:
What do we need to...
Hi Support Team
Must inductors be placed between the SW1/SW2 pins and the VOUT1/VOUT2 pins of the nPM1304? Can VOUT1/2 output normally if removed the inductors? Many thanks...
Hi,
I am working on a BLE application using the nRF5340 SoC(custom board) and Zephyr RTOS (NCS SDK version v2.9.0)
When I call bt_enable(bt_ready_cb_t cb) , Bluetooth...
Greetings, all. I'm a rank beginner here with all things Nordic but almost 50 years of embedded experience with other devices, environments, etc. I'm trying to develop for...
Custom device using nrf5340, with NFC card emulation functionality.
To use the NFC, I understand that I should use the supplied nfc_t4t library (binary) and its api. I have...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
I'd like to use the DeviceTree Visual Editor to create the DTS for a custom board starting with only the bare device. But it seems for some reason that the DeviceTree Visual...
Hello,
I’m using the Thingy91X board (nRF5340). For my application, I need to run BLE and Wi-Fi simultaneously, so I have to increase the application size. To do this, I...
Hi I'm trying to work on OTA implementation for zigbee with nrf52840-DK boards.
there is a sample available in ncs2.9.0,light switch,but i understand it can only work as...
Hello,
I have some issues to do function an ntc thermistor with a nrf54L15DK.
An error about a wrong configuration of the adc reference or or the ADC gain appears almost...
Hi,
I have some problem when scan advertising packet using nrf52840dk with ncs v2.5.0.
when I scan during 30s in the same position, I got a list rssi value same that...
Hi Team,
Hello Team,
I'm currently working on integrating the Sensirion STS40-CD1B-R3 temperature sensor into the peripheral_ht . To do this, I pulled the STS40 driver...
When I used the CS instance for distance measurement, I wanted to set multiple initiators. Therefore, I configured BT_CTLR_SDC_CS_COUNT to 3. However, I didn't know where...
