Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
We want to create solution/project for family of boards using segger embedded studio. We want to create the solution/project in such a manner that new boards software can...
Hello,
I want to build in a reset function for handling certain error states on the 9160DK running nRF Conenct 1.6.0. In the datasheet it appears that nRESET is p0.32 and...
Hi,
I am looking for a way to count the pulses going out of a GPIO pin. If I configure that pin with the input buffer connected, how can I route that signal to a timer/counter...
Hello ,
I am a firmware engineer in Taiwan ,
I already use nRF52820 to finish one case ( cheaper alcohol/acetone BT checker.)
I used USB/ BT wireless uart / Uart send...
Hello,
I have some problems with connecting and interacting with my nRF9160. It doesn't show up in LTE Link Monitor, only got "No supported devices connected" - If i have...
Hello,
nRF52832, SEGGER Embedded Studio for ARM V4.12
We want to improve BLE transmission speed between nRF52832 and iPad mini.
Now condition and transmission speed...
I have two devices:
NRF52832_xxAA_REV2
NRF52840_xxAA_REV3
Running the Zephyr blinky sample application with the following KConfig option added:
CONFIG_NRF_APPROTECT_LOCK...
Hello,
I am trying to create a Matter device by following the steps in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_matter_creating_accessory.html...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
We are preparing NFC with classic tag.(Not connected to nrf52832, separated custom tag) Recently I found that android cannot...
Hi, I have a question to ask: I am using ESB demo as the communication framework. One master corresponds to two slaves, but occasionally there are some problems. Please see...
I would like to implement button interrupt handler. I found two examples in nRF5 SDK v16.0.0. One is examples\peripheral\pin_change_int. And another one is components\libraries...
Hi,
I want to set up a set of four PWM signals that are delayed at a specified interval, just like how the stepper motors are run but the falling edge of the previous...
Hello all,
I am merging the buttonless DFU example with my application for nRF52805.
Everything is well, but I am running out of flash. I am therefore trying to reduce...
