Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I am working with the secure bootloader example. I copied the firmware zip package to my phone. It contains only application.hex in the package, there is no softdevice or...
Hi,
I am working on an application where the device will be in off mode(only timer and BSP initialized in main ) initially and when I long press button_0 for 5 sec the remaining...
Hi,
We are looking for DFU mode GATT protocol source code for reference to implement custom android application which uses DFU mode GATT service to update firmware distribution...
My static code analysis tool complained something, so I took a deeper look and found the following declaration inconsistencies as of nRF5 SDK v17.0.2 in the DTM area. So I...
I am in the process of programming the MAX30105 sensor with the NRF52840 board to obtain the oxygen concentration values I tried to use the library that already exists in...
Hi ,
I am trying to connect my NRF52840 with the application NRF Toolbox using bleuutooth technology when I use this DK
it works very well and the application detect...
I have an nRF5340 DK board. I have followed the online installation instructions and *believe* I have successfully installed (win 10) nRF Connect and Segger Embedded Studio...
Hello, I'm routing on the nRF52833-QI. I want my RF track (ball H23) to go without bends. I don't use J24 ball. Can I remove the ball J24? What is your suggestion? Best regards...
Dear Sir,
Moving to zephyr new installation 1.4.99
The code of getting the IMEI number no longer works.
Modem firmware is mfw_nrf9160_1.2.3
reply_buf_len = at_exec_reply...
I'm trying to connect a 52832 board to a peripheral BLE device. NRF52832 SD: s132 v7.0.1 SDK 16.0.0 As a first step, I'm not setting flters, I just want to connect to any...
Hello,
We are using nRF52840 with SDK 15.2.0, a bootloader and the SoftDevice 6.1.0. We are able to perform a DFU for our application by downloading the .bin and .dat files...
The nRF53 data sheet defines the minimum clock period for teh SPI slave and master as 125nSec - which equates to 8MHz. The SPI Slave also gives the max data rate as 8MHz with...
I tried out a ble_app_hrs_freertos_pca10056_s140.emProject and was able to compile but a couple of questions:
- how is heart rate info calculated? where's the sensor even...
Hi,
I want to write to the NVMC UICR Customer[n] memory addresses during code execution.
I noticed that I can write/read/erase those addresses only before the initialization...
I am testing an example from nRF SDK 7.2.0 on a custom board with nRF51822 QFAAH2 chip. This simple example is ble_app_template adapted for Segger, it should advertise and...
