Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi, I was using nRF52840 ， flash is mx25L25645GM2, I used fatfs with QSPI ,but I found fatfs was unstable,After some time, the stored file would dispear.Sometime there were...
what is credit based flow control in L2CAP connection oriented channel..?
What is meaning of credits..?
what is exact usage in IPSP ..?
How it will effect data communication...
Hello,
I am preparing sniffing workspace for BT Mesh, where I have 3 devices in the Mesh network (provided by nRF Mesh app) and I need to read SRC, DST, SEQ and simmilar...
I tried to run my Thingy91 off the battery but it shuts off instantly.
My questions is if the battery charging functionality is in the firmware or hardware? Trying to figure...
Dear Nordic support member,
Where does "pca10100e folders" be installed?
I have nRF52833 development Kit. But I could not find pca10100e folder.
Note: My IDE is IAR...
Hi, I am looking to develop applications for the nRF5340. After watching the "Introduction to Zephyr RTOS" webinar, I saw that the software engineer presenting the demo was...
Hello
I am making a project in SDK v17. I want to use mpu6050 sensor but I don't know how to use library included in SDK.
The example Martinsbl has in GitHub is optimized...
Hi, i'm trying to find a way to use the Nordic nrf52840 with Adafruit SIM7000-LTE-Shield, the only apparently way is with Arduino IDE but i´m not using it (no success at the...
Various errors during medium-term deployment of cellular-enabled sensor device
We've prototyped an agricultural gas sensor based on the nRF9160, which takes readings every...
Hi,
We are having trouble getting the Thingy91 firmware running as is. We have achieved this in the past but I had made too many modifications and I decided to scrap it...
HI! I'm on Windows x86 and I've followed the steps from the getting started assistant. After trying to locate the board directory ncs/zephyr/boards/arm/nrf9160_pca10090 ,...
I am doing a custom desk for a client and I had this idea of adding a electromagnetic lock on a drawer. That is easy enough but I thought that maybe I could add a couple of...
Hello If I an exemple like ble_thread_dyn_mtd_coap_cli and that I configure the mode in MULTIPROTOCOL_802154_MODE_FAST_SWITCHING_TIMES: do you have any idea how long it takes...
I have two SPI buses on my board, with a different type of slave chip on each. Only a few bytes are read from each during boot. When I use SPIM0, 1 or 2 for them there is...
Newbie here simply trying to run some example projects from the SDK.
Setup:
Segger Embedded Studio 5.10b
Tried example projects in both SDK v17 and v16
nRF52 DK...
