if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hello,
As I understand it, Apple is working on a new product called Airtags. This will be similar to the Tile for finding items like your keys or wallet. The catch is that...
I'm using standard ble_bas from sdk12.3. I set up a timer at 60s interval to use saadc to read battery voltage. Below is my code in saadc event handler for battery level update...
Hi,
I want to add some included services to a new added custom service with nRF Connect, but I can't find a method to do this.
Is there a method to solve this problem...
Hello, regarding to another thread in this forum the debug interface mode can be turned off by sending the command "writeDP 1 0" via J-Link commander or by power cycling the...
Hello,
I'm working with the nRF5 SDK for Mesh v4.2.0.
During the init phase, I call the function mesh_stack_init()
After doing so, the consumption is on average 2.8...
Hello DevZone,
SDK 15.0.0 SD S140
Currently working without an active SoftDevice but even with an active SoftDevice these problems keep occurring.
I'm currently working...
Hello! I need help implementing a TDMA on a nrf52. I've never done this before and Its been hard to find good resources online on the topic so if anyone here has any previous...
I am developing connection between BM833AF Evaluation board and nRF52840, Like a BLE Tag and Beacon. Need support in connection and transmitting data from one to another?...
Hi,
My use case is I have an RGB LED that I want to be green for normal operation, but blink red for 0.5s when a serial driver error occurs.
R, G, and B are each attached...
Hello,
I have multiple questions regarding BL mesh using nRF5 SDK for Mesh v4.2.0
1) is it possible to run this example using 2x NRF52840 dongles(PCA10059) and one NRF52840...
Hello
We have an application that ADV every second and is based on SDK 14.
We are currently attempting to move to SDK 17. What I have noticed is that if I change and...
HI,
I want to use nrf52833 for receiving SAADC DATA in my phone by using BLE_NUS_DATA_SEND.
Here are my codes.
In 716 ~ 724 lines, I added codes about BLE_NUS_DATA_SEND...
Hello
I'm using the nrf52840 DK with sdk version of 15.0.0.
My requirement is to flash my project through cli commands, so I have followed the following steps in below...
Hi,
I recently updated my toolchain using the nRFConnect tool chain manager.
(I was seeing problems after an OS update)
This update fixed my problem but when I build...
Hi,
Please, what are the settings for gpio driver in sdk15.2. for some gpio pin to be able to sink current (to act as gnd? ). In my project it is used for loadswitch enable...
