Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Still having trouble getting a simple Blinky example running on two nRF52840 DK boards configured for a long range PHY_CODED connection.
I've looked through this post -...
I am new to the Nordic SDK and Segger embedded studio, and I am trying to test my NRF52840 dev board.
I am running the "ble_app_blinky_pca10056_s140" example, and I want...
1. Background info
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers...
1. Intro
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers. We received...
Hi,
In case of nRF52810, is it possible to implement both Master and Slave Mode ?
Also, this has do be done while the product being able to work with AT Commands.
...
Power Profiler V2.3.1
Hi,
I recently started doing power testing on one of our boards using the power profiler kit. I wanted to tested current consumption at different...
Hi Nordic Community,
I am trying to build a network using the OpenThread protocol and the nRF52840 chip. I have several Dongles, but I can't figure out how to flash the...
I'm importing ble_app_blinky_pca10040_s132 example in segger IDE. I'm using EVK-NINA-B1 and from nRF SDK I'm trying to importing example but getting error as mentioned in...
I have an external clock running at 3Mhz which I'd like to align with in software. Consider this contrived example:
What would the consequences be of attempting to read...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
Hello,
I'm using a Thread Border Router built using a Raspberry Pi 3 and a nRF52840 Dongle. I followed the steps at this link: https://infocenter.nordicsemi.com/index.jsp...
Dear Nordic Semiconductor support team
Hi, I got your support using micro:bit with nrf52832 by RADIO in the past as follows.
https://devzone.nordicsemi.com/f/nordic...