Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I am using nRF52840 Preview DK (0.12.0) and I want to measure USB currents. I am using the DK as a starting point for doing measurements on custom HW and verifying that we...
I can program and debug using Segger Embedded Studio v4.12 on my mac without a problem. When I try to use the command line to program and erase a nrf52840, I receive the following...
Hi All.
Practising Secure DFU, my nRF52840 DK board seems like if it is locked. Only Leds 1 and 2 are ON. The board is advertising with DEVICE_NAME=Dfu Targ and its COM...
Hi,
I would like to know the correct way to change the polarity of the CS line for SPI devices. The SHARP memory display is opposite of most SPI slave devices so I need...
Hi, I am using the nRF5_SDK_14.0.0_3bcc1f7 with SD v5.0.0 and the ble_app_beacon example together with the Jlink Monitor mode for debugging. The issue is that under some circumstances...
Hi,
I m using now two thingy and I m looking for the possibility to compute the difference between the two accelerometer to determinate the the moment of one compared to...
I'm trying to get back into the swing of bluetooth development, and right now I'm trying to find an overall ladder/timing diagram for a full bluetooth/softdevice transaction...
Is model Publish Retransmit (Mesh Spec 4.2.2.6 and 4.2.2.7) currently implemented in the Mesh SDK? I noticed that with Publish Retransmit Count set to 1, the Zephyr Mesh stack...
In nrf52832 datasheet, it uses" 64 MHz crystal oscillator, using external 32 MHz crystal "
then, can I use external 16 MHz crystal or external 4 MHz crystal to drive nrf52832...
I couldn't find nrf_drv_timer.c file. I want to create timer so I try to different SDK for my work. I am using SEGGER IDE for prepare software but i encountered lots of problems...
Dear nordic,
I try to build BLE application everything works fine expect the UART. The UART has transmission issue.
it has no problem in receiving. but when i tried...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
