[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version: 8.0.0
SDK: 9.0.0 IC:
NRF51822 Rev 3
service: NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
Hi,
Is it possible to communicate with the nrf52840 dongle from an android application via USB port ?
That is, nrf52840 dongle will be inserted to the android phone's...
Take Bluetooth UART as an example, there will be a delay in the process of sending data from the peripheral device to the central device to receive the data.
What factors...
Hi, I'm developing for a custom project board which only has the SWD pins exposed, which I'm using for (1) programming and (2) RTT logging during development.
Once the device...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and would appreciate some insight into how Zephyr...
Hi, I use NCS v2.6.1 I have taken Central and peripheral HR as an example and am trying to modify it to make the Central/Peripheral UART example work similarly.
I briefly...
Hello,
I'd like to add the transmission of an I2C recovery pulse (where you toggle SCK 10 times) to my startup routine for an offboard device whose state I'm uncertain of...
Hello Nordic team,
I was wondering if it's possible to start the MCU boot from the application at runtime.
What I want is to be able to restart my product and run...
Exercise 2 doesn't seem to work for SDK v2.6.1 with v2.6.1 toolchain. SDK v2.5.1 works though. What configuration or code changes do I need to make it work for v2.6.1?
Hello,
I was curious if there was a project that uses 2 Mbps BLE to connect two nrf52840s, preferably with the ability to change which BLE channels the devices use. I...
hi professor,
The npm1300 is used for power management on my borad.When VBAT and VBUS are connected simultaneously, the bulk 2 output power supply varies between 1V and...
In our custom board, check flash write and read using sample (C:\ncs\v2.6.1\zephyr\samples\subsys\nvs) but showing following response. the same build working fine in nrf7002...
This issue is for a programming environment on a macBookPro.
I finally get the system tamed and got to the point of testing the various sample apps provided. I wasted a...
Hello,
I have trouble again with TX Power control. This time using Softdevice Controller and NCS2.6.0.
Previous issue which was solved (this was using Zephyr Controller...
1.Created a composite device for CDC and MicPhone. When the registration of mic SOF is interrupted, the device may not recognize the issue
ret = app_usbd_audio_sof_interrupt_register...
Hello,
OS: Ubuntu 22.04
SDK version: NCS 2.6.1
Modem firmware version: nrf91x1_v2.0.1
We are evaluating NRF9151 in a new design. We have some prototypes built...