if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
Ours is a battery (LiPo) operated device with VDDH= 3.0 to 4.2V. One of the reasons for using nRF52840 is to avoid an expensive external DCDC IC. But due to the Anomaly...
I'm trying to follow the DevAcademy Intermediate Lesson 5 Exercise 2 using an Elegoo shield instead of the Adafruit one.
The shield I'm using is this one: https://www.elegoo...
Hello, we have built a BLE device based on the 52840 chip and the nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_mouse example architecture. We have built a...
Hi,
1. The customer would like to know which values are configured for which registers of nRF5340 by the following instructions?
nrfjprog --family NRF53 --coprocessor...
Hello!
I am using an nRF52805 for a custom board design and I am hoping to get some advice on selecting peripherals and Zephyr features that would best meet my system...
Dear Nordic
hardware:NRF5340, sdk:2.6.1
Our project needs to use floating-point calculations. Attempting to add CONFIG_FPU=y and CONFIG_FPU_SHARING=y to prj.conf will...
I use GNSS with the timout at 0 and interval at 65535.
I do not really need the location but is it nice to have a kind of a log of it because it is available en power consumption...
Context: We are planning to connect the nRF9151 to a private test network using a coax. cable. for development debugging.
(#1) Do your modules support SIM cards with test...
Good day
I have a lwm2m client running on a custom nrf9160 board. I would like to run everything network related to network on a separate chip. Assuming that the two chips...
Some guidance on this query,please. I have a project with several freestanding application (please check topology below). I would like all the apps to acccess a custom board...
Hi,
I am currently configuring the nPM1300-EK with the nRF5340-DK by following the instructions from the webinar "Adding battery charging and fuel gauging to your nRF52...
For a device like the nRF9160 Feather, you need a second USB to UART device for listening to the modem traces. When I go to select the Terminal Serial Port under Advanced...
Hi All,
Im very new to this how firmware space and would love some help.
Currently i have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
1. Hi i am using nrf52840 sdk ver 17.1.0 in secure bootloader /pca10056_uart_debug
2. I have flashed the dfu uart code without any change
3. while performing dfu via uart...
We are developing a ZigBee-based end device using the nRF52840. We have implemented most of the functionalities and also reporting and are able to receive reporting information...
