Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
Hi,
I'm developing some projects with the nRF51822 chip and I am not able to debug them successfully any more. However, I have previously debugged correctly some projects...
We're using nrf52833 and our target board is already running our program well.
Then
we'd like to flash by using Jlink SWD programmer.
So, we connected vref, gnd, swdio...
We have found a nrf52833 DK (PCA101000) with id, 685888541 with 2024.4.
So, it might be used as previous project in our company.
Anyway, I tried to test with this DK board...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hi
I have a nRF52832 Device, and develop by nRF5 SDK 17.1
Now, I have a project base on BLE_Central \ ble_app_uart_c , and also need to use Dfu OTA function
so I refer...
Is there a way to modify the distance measurement sample code to where it is intended for one transmitter and multiple receivers versus between just two devices? I am trying...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
Hello.
I am trying to run an alarm clock using the RTC calendar. In the main loop I see the time being printed, but there is no response from the alarm callback, which I...
Hi,
in my case I need to flash the nRF5340DK board with only a standalone merged_domains.hex , which I get from another co-worker, no source code. how to do it?
Best...
Hi.
I wanna evaluate nRF52840-DK. However, when I tried to install Toolchain on Visual Studio Code, a message "Failed to fetch available toolchains." is displayed. "nRF...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
Greetings to everyone.
We have the nRF52840-DK, where the Power Switch SW8 physically is broken.
Is there any way (a bypass, making a bridge/shortcut, using a soldering...
HI everybody,
I have problem with my Nordic nrf9151-DK. I am not able to use GNSS with this kit. A looked at documentation and found, that i have to activate XCOEX0...
Hi,
I have been using the nRF52840 for a long time, and everything was working fine. However, now LED5 starts blinking whenever the USB is connected to J2. I have tried...
Hello, I am new to using the nRF platform, and I appreciate your understanding. I am currently using SDK 2.8.0.
I have implemented a thread in the application core to acquire...
