Hi,
We've been seeing an intermittent connectivity issue in Yosemite in discovering BLE services, namely scanForPeripheralsWithServices does not return anything. The same...
Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
Hi!
In previous versions of the SLM it was possible to provide a hex datatype to the XUDPSEND command to send blobs of data over UDP, without having to worry about a stray...
Hi,
I enable the watchdog in the application image, then call soft reset to enter the bootloader, the bootloader execution is also normal, until the watchdog is reset. ...
Hello!
I have a situation where a chip is connected with an antenna on a u.FL slot, what I want to do is to remove that antenna from the chip and connect my nrf52840 to...
Hi,
I want to send the I2S MIC Raw data through Ble by using ble_nus_send. I have written one application but it triggers a Cmake error. I have attached the log below...
HI I'm using the nrf5340dk, and I'm able to flash the application core with code that toggles the LEDs.
But I'm not able to flash the network core. I've specified in the...
Hi, I'm currently designing a system which requires Heart Rate monitorization and I'm using the MAX30101 chip to do so. I will be using I2C communication and, therefore, based...
1. We use code similar to the existing sample code to repeatedly sample a 0 - 2.25V voltage range using the SAADC. 2. Settings: 30s interval, single-ended input, burst-mode...
Hi All,
I'm looking for a PC based tool with similar functions as nRF connect. Our manufacturer is developing a functional test fixture which will PC based and will be...
Hello,
I'm looking for reading the sent data from an old embedded autonomous nRF905 (which act like an active tag) and I thought I could use this convenient-looking USB...
Hi,
I am using nrf52810 with custom board and i want to create OTA file for custom application. while compiling the bootloader to get hex files, i am getting error as "Target...
from the datasheet we see that this device can operate at 1.8V or 3V3 (or anything in between).
We can also check supply current on the mRF52DK which runs at 3V3.
How...
