Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi,
I am trying to measure my circuit sleep current while connected, through a high value resistor, the problem is while waking up each MIN_CONN_INTERVAL the processor wakes...
It is found that under the same routine in zigBee SDK, the project under pCA10056 folder can run normally without burning the protocol stack, but the project under PCA10059...
We would like to stream data through an l2cap channel from a nRF52840 module to a smartphone. The l2cap connection is initiated by the smartphone, I configured an l2cap tx...
I would like to test some compatibility features using the nrf52833 DK as a Bluetooth 4 transmitter instead of Bluetooth 5 (which it is by default). I do not see an explicit...
hi support team，
i have two questions from customer.
1. Monthly review suggested that Verizon certificate will be on October this year, how about he progress, we have...
I'm using the Nordic UART Service to implement BLE communication between an iOS app (central) and a Raspberry Pi (peripheral). Whenever I send a large payload to the central...
Hi,
We are using Nordic thingy 52 HW and their SDK for our Evaluation purpose. We are using Nordic thingy 52 microphone code directly. That firmware is using ADPCM codec...
Unable to connect to Bonded weara with GATT 133 error. Currently, there is only one solution, turning on and off Bluetooth in the OS, which temporarily improves the connection...
Hello
new nRD5 SDK v17.1.0
Can you please help me to find more about:
1. "- NRFFOSDK-13484: Added an option in the Peer Manager to decide that a connection will not...
Hello,
I am currently developing an application on a single core application. I need to add a BLE part to this application. Currently, I have an OTA update procedure that...
Hello,
I'm trying to open an L2CAP connection and send some test data to the nrf52840 dev board from my computer. But my connections were timing out with 'Page Timeout'...
Hi ,
I have a question ,according to the official configuration and example, the ADC sampling voltage value is smaller than the actual voltage value. For example, the actual...
I have nrf52832 dk and soft dveice s132 am using ble app template code.
I need help in this code that as:
1. as i flash the code on dk, the device should be initally in...
I am using NCS v1.7.0 and have found that SES is not being configured properly for debugging/flashing. When I open the project in SES, building works fine, but when I try...
