Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello,
I have been trying to follow tutorial from:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/mesh-networks/posts/thread-tutorial-practical-guide-for-device...
Hello,
through figuring out how AWS FOTA works and following the instructions of this page
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160...
I found a couple of threads that the Windows version of the Power Profiler App in nrfConnect is broken, which it is also for me. It used to work in the past and I also like...
Hello there,
During my development I have discovered an issue with app_timer library. It is fragile for calling stop/start functions from interrupts which has higher priority...
Hi,
I have a project with nrf52832 without any BLE operation. Software runs with FreeRTOS. I am trying to add ble dfu into this project. There is a button connected to the...
Hi,
I am using nrf52832 development board with sdk 17.0.2 and softdevice 132.
I have freertos project which had ble nus service and aes cbc logic added to it.
I have...
I am trying to run the ble_app_uart from the ble_peripheral folder in the NRF SDK 15_2 I am testing with a Nordic 52840 DK (PC10040). I have made essentially no changes. ...
Hi, Nordic staff.
I'm working with Central device using S132.
There is a peripheral device using S112 in Nordic. I didn't make this peripheral.
My question is...
Hello all.
I have a question relate to: How to "ble_app_hids_keyboard" app can connect multi device?
My task: make equip peripheral base on nrf52811/840 can Adv and connect...
Hello, I am new to Nordic, I was previously using Cypress CYBT343026-01. But there were some drawbacks found during development. 1. It was consuming 315μA at 0 dBm BLE tx...
Perusing the GCC linker script supplied as part of SDK v16, I noticed that the .data section is specified as follows:
.data : AT (__etext) { __data_start__ = .; *(vtable...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
Hello
I'm going to use a potentiometer to control the pwm. I am using a 10K potentiometer and have used a saadc example.
I printed out the value of adc through this example...
