Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Hi
I am new to nordic processors.
I am using spi_ pca10040 project as a reference for my custom board. On my board the SPI pin configuration is different from pca10040...
I understand the reason for the polygon cutouts under component pads in the RF nets in nRF9160 DK design (and others). However, at LTE and GPS frequencies this doesn't seem...
Hello,
lately I've often noticed problems while reaching nordic devzone, the server is often very slow and will sometimes not respond at all. Is it just me here in germany...
Hello guys,
I programmed the gps sample on the nrf9160 DK, but I get:
I added a printk to see which of the at_cmmds were failing but I get inconsistent results. It used...
Hi,
Working with ads1220 which runs on SPI. There standard SPI pins - dout, din, sclk, drdy. In its datasheet there is written it is possible to merge dout with drdy to...
How to upload code to nrf52840 using arduino or usb2ttl as I have ms288fv2 help me guys or suggest me the board using which I can upload to code to nrf52840 if and ms88sf2...
Hello:
I'm testing nrf9160's A-GPS function, and I find that an error of SUPL will be reported at runtime:
I use master branch of the nrf repository(nrf/samples/nrf9160...
I have a Windows 10 laptop (Acer Swift SF 514-52T) where I have installed the setup for nRF9160 from "nRF Connect for Desktop".
All steps followed.
I got some issues...
I've got my application wrapped in mcuboot for HTTP-based firmware updates which is working fine. In the past couple days I've enabled CONFIG_NVS using the code in zephyr...
Hello all, This is my first post on your DevZone. Setup details: nRF9160 DK Board: 0.8.3 nRF Connect SDK tag: 1.2.0 OS: Windows 10 Pro LTE Network: NB-IoT on B3 and B20, Operator...
Hello, I'm using nRF52811 and It works with 1.8 voltage on it's VCCs. Is it possible to use a micro SD? Should I use a voltage level translator (for example TXB0108)? I know...
Hello all,
I try to import Keil project into Eclipse with Makefile. I managed put all my source file to be compiled, and my include paths etc.. in my Makefile
In Keil...
Hi,
I am working on one application in which I want to sample ECG at 1000 samples per second continuously and battery value at 15 seconds interval. I am configuring two...
Hi,
I'm trying to connect my phone ober BLE with the nrf52840. The first x attemps always work (connect, disconnect, connect, disconnect, ...) but after some time no further...
Hello guys,
I`m pretty new in socket programing, I have a question , is there any way to trigger an event for a file descriptor that is used in poll() function ?
For example...
