Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi,
I try to develop a Bluetooth speaker using the nRF 5340 DK since i do not have a separate audio Dk for this. I am using the sample code Audio unicast client for this...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
Hi all,
I'm looking into speeding up my workflow using remote development containers on ARM servers, but it seems some tools are missing, nrfutil the first, to run a fully...
When I get a custom board, how do I detect and flash it? I have three options on the board:
I have a USB cable with:
GND
D+
D-
+5V
OR can configure the usb...
Hello, I'm trying to get nrf5340_audio example running on nrf5340 audio dk.
I'm able to build the code and run it however i'm unable to bond with my mobile phone with android...
Hi! In order to get more accurate battery SOC measurements I need to provide a custom battery model to the app. So, I had to use the nPM1300 EK + Fuel Gauge board to profile...
Our device is set up to provide AT Commands directly to nRF9160 using a USB UART connection and control using a VT100 Terminal simulator. When attempting to connect to the...
Hello. I'm using npm1300ic. In one example, there is a battery_model.inc file related to li-po 3.7v 200 mah battery, and the battery you are currently using is li-ion 3.7v...
When dynamically allocating BLE GATT services and characteristics using custom structures and Zephyr’s dynamic memory functions (e.g., k_malloc, k_calloc), the service registration...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hello Nordic team, Whilst porting our product from nRF Connect 2.4.1 to 2.9.1 we encountered the following problem. When compiling with ZIGBEE_FACTORY_RESET=n we get Seems...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
i'm looking for an extremely simple BLE beacon app, which advertises (say) at 1HZ and then enters a "low-power" sleep mode....
there are numerous samples included in the...
Hello forum ,
In here i will upload my project in zip where i m using w25q64 flash -nrf52840 .i m trying to read data of qspi flash read write and read for an two byte(trying...
I am in the process of integrating a custom display driver (ST7305) into my Zephyr-based project and have followed the necessary steps:
Placed the .c and .h source files...
