I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
I'm trying to set PWR_UP bit to 1 for the device to go into standby-I mode using STM32F103RBT6 and HAL libraries.
I send (0x20 | 0x00) command (write_reg | config reg)...
I'm trying to compile the S332 example project ble_ant_app_hrm_pca10040_s332.uvprojx. I'm using the V12 SDK and Keil uVision V5. When I try to compile I get an error saying...
Starting with "Development with GCC and Eclipse", I've gotten "blinky" to run on my BLE400 with an nrf58122 using Eclipse Oxygen. I think I'm using SDK12.3 . I started with...
pca10040 S132 5.1.0
if i run only a single nrf nus service (rx and tx) at 4 k bytes / sec both directions, how much load would this put on the 52832
the test is assuming...
Hi,
I'm connecting two I2C modules : MAX30102 and MPU-9250
I can individually communicate with either of these modules and they work okay. But if I connect both of them...
Hi Nordic,
I noticed that both Write Without Response(write_wo_resp) and Write(write) can be enabled at the same time when add a characteristic. I know it means both types...
HI all:
If the iphone saved is English name i can parse it out, But if the save is a Chinese name I don't know what is to use the utf-8 encoding and unicode, who has successfully...
Hi，
i defined spis rx and tx buffer length at:
#define HUB_SPIS_RECV_BUFF_SIZE 1024
#define HUB_SPIS_SEND_BUFF_SIZE 1024
because the rx data length will be vary...
Hello nordic
I use ble to create custom services, I want to create an embedded system that can create and send and receive data. I am using sdk version 14.2.0 and what...
Hi,
Im currently designing a custom pcb using nrf52 reference design available here . In my design, I have to connect the ground of two analog signals to VSS of nrf52832...
I tried Blinky blank application on PCA10040 by IAR. By pressing "Download and debug", everything is fine, I added RTT debugging information and can see it from RTT viewer...
I Have an issue trying to flash a nrf52832 custom board.
Something extrange happens because when I download an example from keil that blink a led(gpiote_pca1036(nrf52 PCA10036...
We are using s110_nrf51_8.0.0_softdevice.hex soft device and nRF51 SDK v10.0. We have below questions in case of soft device assert scenario.
In what scenario's soft...
Hello,
I am working with the example of PDM example on the nRF52832.
And over this I would like to use the drv_speaker. I put all the files from the Thingy 52 example...
On a system using an NRF52832 with S132 softdevice (without no external LFCLK XTAL), in low power mode via sd_app_evt_wait() - we see a nominal current of ~3uA with a periodic...
