Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hello all,
Currently, we are using the nRF52840-DK and realized that the interface to upload programs is very handy (being able to simply drag a .hex file onto the device...
Hi,
after updating my NCS version to v2.1.2 I noticed that my Zephyr SDK also needed updating from 0.14.1 to 0.15.1. However, after updating my Matter project does not compile...
Hello,
When using two nRF52832 modules for Bluetooth connection, can it prevent Dos attack program? We have found a situation where a malfunctioning or malicious client...
Hi,
I am evaluating the nRF5340 Audio DK and measuring while adjusting the audio bitrate.
I found the following 3 symbols definition for bitrate.
CONFIG_LC3_BITRATE...
Hello
I got a nRF52840 DK and try to use Direct Test Mode APP (v2.0.3) in the nRF Connect for Desktop (v3.12.0).
However, it always says "Can not communicate with device...
I have sdk 2.1.0 and nrf5340, trying to run peripheral_uart sample connecting nrf5340 to a module via uart. The program seems working when only works with nrf5340 based on...
Dear Nordic Support Team,
I wanted to configure the nRF52840 dongle as radio co-processor. For that I wanted to build and flash the Thread: Co-processor sample in nRF52840...
Good day
I intend to use a power saving mode to turn on a device for a set amount of time. During this, the device would still need to receive commands over mqtt. Is this...
Dear SRs
We are evaluating your NB-IoT solution by means of Thingy91 reference board. The NB-IoT service is working with iBASIS card, the question is: can we change the...
I've created the samples for Socket Echo Client https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/zephyr/samples/net/sockets/echo_client/README.html#sockets-echo...
HI , I am having difficulty in interfacing the flash with my DK board
1) The spi flash sample is getting stuck at flash erase function without any error responses
2) I...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
