I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
I have been trying to implement the wifi scan or wifi provisioning code on a module (MS12SF1) which is a combine wifi + ble module
The setup looks like the image shown below...
Hi,
I'm developing with NCS v2.6.0 for Raytac MDBT53v-P1M module, which inhibits nRF5340. I already have my own PCB with all the required HW components.
As a sanity check...
Hi I would like to report a bug in the Devicetree visual editor.
When you add two fixed regulators and connect a separate sensor to each of them, both sensors will be represented...
I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hi, I am experiencing low power issues on a nRF52840 DK 3.0.2 board which I have not seen on another one with version 3.0.0. I do not know the root cause yet.
For my investigations...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
Hi,
I have a new NRF5340-DK and I am trying to connect it via usb on linux but do not see it in the syslog when connected. I actually do not see anything at all.
When...
Hi,
I want to implement a pwm output signal on a particular pin of the nRF52840DK working with the latest nRF Connect for VS Code. What would be the recommended way to setup...
Hi,
I tried to flash the blinky example to an nRF52840 Dongle as described here:
https://academy.nordicsemi.com/flash-instructions-for-nrf52840-dongle/
Console output...
Hi I'm trying to create a transparent CDC to NUS bridge, this is based on the nrf52840 dongle.
The Aim of this is to send binary files to our device from a PC, our device...
I wrote a code for GPIO interrupt when DRDY pin goes high to low(Data ready) interrupt should occur and call a function but it is not working Below is a code:
intDRDY =...
Trying to implement FOTA DFU over BLE. My application uses my proprietary code (instead of mcumgr) to download signed OTA firmware image to secondary slot (in my case it is...
I am working on an application with significant constraints on power consumption and distance immunity. After some research, I found the Thingy:53 module, which is well-suited...
We had tried AT#XSLEEP=1 command in nRF SDK 2.5.0 and it worked. We saw it working for both modem FW 2.0.0 and 2.0.1.
When we updated SDK to 2.6.1 and modem FW 2.0.1, the...
