Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Why do I often fail to compile the examples due to west? The prompt suggests that I need to upgrade west, but I am unable to do so?When directly upgrading West through VSCode...
The solution for "nRF Connect SDK Intermediate - Lesson 9 Exercise 5" does not appear to boot-up after flashing and gives the following output on the com port:
*** Booting...
Currently with the DECT NR+ modem API on nRF91x1 I can schedule rx operations in mode NRF_MODEM_DECT_PHY_RX_MODE_CONTINUOUS given to nrf_modem_dect_phy_rx via nrf_modem_dect_phy_rx_params...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
Hi,
I am working on nrf52832 and using SDK 16.
I try to debug the ble_app_buttonless_dfu example, which give error on line 853 in main.c. err_code = ble_dfu_buttonless_async_svci_init...
We are in the process of developing a product using the Thingy91:X as reference.
We need to modify the hello-nrfcloud firmware to suit our application.
Could you suggest...
I am currently working with the Matter sample project and have encountered a question regarding the diagnostic log function. I would like to inquire about how to enable the...
I'm using nrf52840, v3.0.2, scanning BIG/BIS and printing out the BASE.
I first scan the extended broadcast with the label broadcast_id, and then establish synchronization...
I wish to install this program as stated in nRF Connect for Desktop. The install hangs at Downloading files... I am on Windows 11. I tried a few times with the same result...
I am puzzled by what I have observed using retained ram on NRF54L15. I have this overlay (see below). Essentially created 16 KB SRAM at address 0x2002C000. I have a struct...
We are trying to add ble mesh functionality to our current product, but encountering an error.
We are copying code from the ..\v3.0.1\zephyr\samples\bluetooth\mesh_demo...
