SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Hello
In the past I was able to run DFU on both SDK 17 and SDK 14.
Now I am developing over SDK 17.1.0 a new application and attempted to run secure DFU Bootloader using...
Hello, I am working with nRF52832 (PCA10040 DK) on nRF5 SDK v17.1.0 with SoftDevice S132 v7.2.0 . I started with the ble_app_uart example and added a custom BLE service ....
Hello everyone,
I have some questions regarding the registers of the nPM1300 specifically for the load switches and LDOs.
In the data sheet in chapter 6.5 under "Load...
Dear Nordic team.
I am a beginner learning to connect a SPI devices with nRF54L15-DK but the program always reports errors. Here are my related codes:
nrf54l15dk_nrf54l15_cpuapp...
NCS SDK and toolchain: nRF Connect SDK v3.0.2
Boards: nRF52DK-nRF52832 , nRF54L15DK-nRF54L15
Issue:
After un-initializing and then re-initializing MPSL, MPSL no longer...
Hi,
We are using the nRF Device Manager app (Android) to update firmware over BLE to the nRF54L15 DK, and it was working fine until August 26, 2025, when the app was updated...
Hello, I followed the "DFU over UART" exercise of the intermediate lesson 9, and I have problems with launching the main application. I'm using nRF54L15-DK board, SDK v3.1...
Hello.
I'm currently migrating our existing application code to the NCS 3.1.0 SDK. As far as I have recognized, with sysbuild the child image build has been replaced. We...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hi, i am trying to onboard our custom board using a nrf9160 to nRF Cloud using this guide: https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/cellular/nrf_cloud_multi_service...
Hi we are developing a prototype with NRF5340DK, for which we needed to control few set of GPIOs. we wrote our code in the assumption that it's pretty straight forward and...
Hi,
I just updated my vsCode extension and the visual devicetree editor stopped working
I can compile just fine but changing the DT will prove difficult from now on. ...
I used the official example provided by Nordic: github.com/.../nrf70-wifi-ble-image-transfer-demo . I followed all the instructions to complete the preliminary configuration...
1. can you tell in detail about Easy DMA supporting on SPI, I would like to understand how I can utilize DMA feature for communication with RAM over SPI what is the added...
Hi
We have nPM1300 evaluation kit, we use SW1 VOUT1 1.8V as VINLDO1 input, we remove jumper JP7(for LS_LDO_OUT1 connect to R8) on P15 connector, and provide 1kohm loading...
