SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
I flash v1.7.0 at_client and mfw-v1.3.0 into nrf9160-DK board, LTE works normally and the board can get the ip. ( https://files.slack.com/files-pri/T0SBEQ7AR-F02J4REC8RX/nordic...
I'm trying to implement communication protocol that involves clock and bidirectional I/O line. Clock signal is coming from an external device and expected to be in 1-5MHz...
Hi,
Could you please help to fill which nRF9160 SIP revision fit for SDK?
nRF9160 modem firmware version
nRF Connect SDK
nRF9160-DK, SIP revision (BA, B0,...
Hello,
I have a question about the best way of implementation.
The data will consists out of a struct with multiple pressure and temperature measurements coming from another...
Hi everyone,
I have this question to ask. So I am trying do make an end device that run on low power. I can see that there is an example about the sleepy end device in the...
Hello everybody,
I wonder if somebody could give me an example of an easy way to use saadc without using any adc_event_handler for sdk 15.
I'm trying to do it myself from...
Hi,
I connected an external MCU and going to run AT commands sequence by using serial port (UART2).
Can someone provide the sequence of AT commands to get fixed A-GPS...
Looking for advice on reading data from the BL654 UART RX pin which is getting a text data stream from an STM32 micro.
I tried the "peripheral_uart" sample app in Segger...
When "Zigbee Dongle" is successfully connected and communicated with terminal devices, if the terminal devices that have been successfully connected to the network are all...
Hi there
We are trying to modify the MQTT_Simple example to be able to send more info than the status of pressing a button and having a button pressed notification go back...
Hi, I wanted to merge two example projects: "ble_central/ble_app_uart_c" so I have central client application, and a "peripheral/ble_usbd_ble_uart" so I have working USB CDC...
Hi everyone,
Im working and learning for private project CAN bus sniffer which when receive some data trigger some relay...
I have mcp2515_can hw-184 board on which Im...
Hey all I've had some issues with the zephyr installation and have followed the steps for setting up the toolchain. When im building a project from the command prompt it fails...
Dear Sirs,
In my current project I use nRF52 and external ADC. I have to send 14 Bytes each 500us using UART to PC.
It is only one way connection where nRF52840 is transmitter...
