SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
To the kind attention of Nordic support team,
About nRF52833 product specifications (8. recommended operating conditions)
"Note: The on-chip power-on reset circuitry...
Hi,
I'm trying to run a pc-ble-driver on Arm64 arc
I've compiled the pc-ble-driver to arm 64 from this release: ARM64-linux pc-ble-driver origin/release/4.1.2
I used...
Hi,
I'm currently working on a way to connect raspberry pi as a gateway into the nrfcloud. For this case, I used nrfcloud/gateway-raspberry-pi. Neverless, when I tried to...
I am developing a product using nRF9160 and found the power consumption is higher than the datasheet. So I want to use Matlab ti simulate the circuit to see where the error...
I am currently trying to implement a Thread functionality on an nRF Dongle connected to a windows machine. Its intent is to be able to recieve messages from other thread components...
Hello Nordic team,
I have a nrf9160 powered from a 3.8v bench supply.
I also have a usb to uart cable , with uart wires going into NRF9160. Usb side, plugged into my computer...
Hi
1、 The following table does not indicate whether the QDID belongs to 5.1 or 5.2.Are the QDIDs of softdevice classified as Bluetooth 5.1 or 5.2?
2、The following qdid...
Hi all!
I flashed and got both SoftDevice s130 and the example code onto my nRF51802 without prior modifications.
I flashed softdevice according to: https://infocenter...
Dear Nordic Team,
Hope you all are doing fine.
I have the NRF52-DK based on the NRF52832 BLE IC from Nordic. I wanted to implement a basic BLE Beacon that broadcasts continuously...
Hello,
I am starting to work on a sample project, wherein I need to replace the existing "main.c" file I have with "main.cpp", by copying the contents of "main.c" into...
Hi zone,
I've just got nrf9160dk and test gnss feature. Issue is: 1. Device get long time to fix. Even which many SVs in tracking and using
2. After got fix, device...
Hello there,
Recently I tried to configure the MCUBoot on my custom Adafruit feather nrf52840, based on the Windows.
Firstly, I followed the instruction below to configure...
Hi
I use PCA10040DK,My connection description：
DK's External supply + to the PPK2 logic port VCC pin DK's External supply - to the PPK2 logic port GND pin DK's External...
