Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
in my own board. I start a spi master.
and capture the signal of the CSN and SCK.
they looks abnormal
in one burst (package), the CSN has two pulse. I think the CSN...
I'm just using nRF24LE1 to make 2.4G wireless mouse, mouse sensor is PAW3205DB-TJ3T. But i got a problem, PAW3205DB-TJ3T uses two-wire spi(SCKL+SDIO), nRF24LE1 only supports...
I am trying to do an OTA update of the firmware on my device. I am using Nrf Connect SDK 2.1. I followed some of the tutorials and setup the device to advertise the SMP UUID...
I am using the VSCode extension (2024.12.55), nRF Connect SDK ( 2.9.0). I created a new project from the USB loopback sample to investigate how to configure a project for...
Hi,
I suddenly started getting MPSL ASSERT: 112, 2134 upon BT enable and upon research came across this post ( link ) and used following code:
HFXO starts on peripheral_lbs...
Hi,
We are developing a new project using the nRF52832 as our controller and nRF5 SDK 17.0.2 as our SDK.
We have integrated the NUS client and NUS peripheral parts from...
I have an application where I use the bt_gatt_write() method and I would like to obtain information about the number of packets sent in my operations.
I would like to know...
Hi,
I am baffled by the QOS handling (and/or not handling) in asset_tracker_v2, especially in view of the fact that there is a QOS library as part of the nrf repository...
Using the nRF Connect Desktop application and the nRF Connect SDK for my nRF9160dk.
I would like to monitor RAM usage during runtime of my program. In particular I am interested...
Hello,
I am trying to migrate a project nRF Connect SDK v2.6.2 to v2.7.0 for the nrf5340dk target board, particularly to update to the new hw model v2 and sysbuild. I am...
Hello,
I am using nRf21540 and nRF5340 in GPIO+SPI config, where SPI is controlled via MPSL and separate spi0 bus.
I have configured the board files based on nordic,nrf21540...
devicetree overlay file
// * Connecting ADC channels
// For more help, browse the DeviceTree documentation at docs.zephyrproject.org/.../index.html
// You can also...
I just ported your AWS IoT for MQTT from this repository .
If I keep IPv6 enabled, I can get the address information without any problem. However, if I disable IPv6, the...
I have a project that runs fine when CONFIG_BOOTLOADER_MCUBOOT is disabled, but when I enable it pins 15 and 16 are pulled high. I need the mcu bootloader to run but is there...
