Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hi
I'm trying to ackquire a GPS fix, and then transmit it to my server as a UDP packet.
First, i enable the GPS with the AT%XSYSTMMODE at command, and then try to enable...
SDK 17_0_2
Hi!
I can't understand is it any possibility to wake up nRF32 from sleep mode via internal RTC timer?
For example- I set ADV duration 30 sec. After that time...
Hi Nordic team !
Is the licencing model linked with the Nordic OTA libraries available in github allows me to freely fork / modify / share a compatible version for Xamarin...
I have define CONFIG_NFCT_PINS_AS_GPIOS, but the pin is always low, even if the OUT register is high.
I have read 0x1000120C(NFCPINS), it is FFFFFFFF, what's wrong with...
Hi, After many attempts I was unable to make RPC_Host sample work ( link to the related nRF Connect SDK doc ). From SES in debugging mode, the network core gets stuck in an...
Hi,
I am writing a program to actively change the state of an LED, then sample the output voltage on the led pin using SAADC, then outputs the adc value to terminal every...
I bought the nRF52840 DK and want to start developing my first application. However, I am very overwhelmed by the documentation here infocenter.nordicsemi.com/index.jsp This...
Hi All, I have a problem with the UART interrupts on the nrf9160dk, the error code (-134 / -ENOTSUP) says that it is not supported. However, I don't know what might be the...
Hello everyone,
I'm unable to perform DFU over SMP BT with nRF Connect for iOS. I've already verified the process works with mcumgr (Ubuntu 20.04 LTS) and with nRF Connect...
I am trying to use the `fmfu_smp_svr` sample project, as described in nRF9160: Full modem firmware update using SMP Server , to perform a full modem firmware update.
The...
Dear ,
I am going to use SDK 17.0.2 spis example.
But I found it is 8 bit data width. I am going to use 16 bit data width .
Would you teach me how to change?
Hi all,
I am using NRF5340, and I want to use pin 0.14 for spim. However, I found it was used by QSPI, in zephry.dts:
So how can I close QSPI to use pin 0.14 freely...
Hi.
Below is used the same schematic for nRF52805 but with different placement for RF components.
What are the pros and cons of each one? Is there one that is "better...
Hi !
I want to successfully send CTE after the CRC of the broadcast packet by operating the RADIO register under the Manual configuration of NRF52833。At present, I can successfully...
