I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
I am building and running the Serial LTE application on a nrf9160. But am facing an issue with the application going into a reboot loop when network is activated.
I am using...
Hello,
I am working on building a BLE peripheral using the nRF52 DK board. I want to create both connectable advertisement and unconnectable advertisement (beacon type)...
Custom nRF9160 hardware. UART0 over RX/TX-TTL. Updated to MFW 1.3.6. nRF SDK 2.5.2.
Two issues:
1)
Normal at_client w/ PDN enabled to set APN. LTE Link Monitor, and...
Hi
I have a question regarding the power consumption of my own PCB.
I have taken a power profile of the nRF9160DK dev board and of my own PCB with the same software, but...
Hi,
I was looking for a way time sync among nrf52840 devices and I found "Wireless timer synchronization among nRF5 devices" guide and the git hub.
However, it seems...
Since upgrading to macOS Sonoma 14.4.1 yesterday, I can no longer use my NRF52840 DK (PCA10056). The `JLINK` drive momentarily mounts and then disconnects. This process repeats...
Subject: Assistance Required: Troubleshooting nRF52840 and nRF52832 Connection Issues
Hi,
I am currently working on a project involving a nRF52840 (S140) serving as the...
Hi,
I am on nrfConnect SDK v1.7.0, with a nrf52832, with UART in ASYNC mode.
During the uart event callback, the event type UART_RX_STOPPED, but when I check for the error...
I am having issues getting the LVGL library working with my nRF9160 Feather . I am using SDK version 2.5.0.
I have narrowed it down to the call to: `lv_task_handler()` not...
Hi,
Starting from the AWS IoT sample, I’m having a hard time configuring the connection before calling net_if_up() which abstracts a lot of stuff. I would like to configure...
If you try to write a program on a board with nRF5340 installed, an error will occur.
I can write to other boards using the same J-Link, so I don't think it's a J-Link problem...
I disabled the DIS. With nRF52DK the custom services characteristics are shown but if I upload the code to the ebyte e73-tbb, the custom service and characteristics are not...
I am following this page regarding Matter commissioning using the CHIP-TOOL.
I am using Ubuntu as the host for development and running the chip-tool. I want to commission...
