I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I'm upgrading from SDK version v2.4 to v2.7 which introduces the new Zephyr hardware model and I'm struggling with the transition. I have two custom revisions is based off...
Hello,
I am using nrf7002dk on NCS version 2.6.0.
I want to send data to an HTTPS web server using WiFi.
I saw some mentions about HTTPS in several posts on Devzone...
HW/SW Versions:
nrf52840 Dongle DK
nrf Connect SDK 2.5.2
Issue:
I'm developing a Zigbee device based on the ZBOSS, using an nrf52840 dongle development kit and there...
Hi,
We have developed a nrf5340 custom board powered 1.8 V. So we cannot use the nordic DK board to program it.
I would like to know if there is an interface other than...
I have an application where I am using the SAADC to take ADC samples. At any point during the measurements, I want to be able to stop the samples prior to the ADC buffer filling...
Hi,
I trying to adapt the ble_app_multilink_central example to allow more than 8 peripheral connections to the central device. However, when I change NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi,
I am using nRF52832 board and I want to understand the current consumption in the board will differs while running the code in zephyr RTOS platform and without zephyr...
Hi,
I would like to know where Matter's commissioning ad timeout is set.
I understand that it stops after 15 minutes, but I don't know where it is set.
Best regards...
I am currently learning nRF52840 , I started the BLE fundamentals course , and this the lesson 1 exercise , It Worked Fine , after the lesson 1 , none of the lesson's exercises...
Hello, I want to update the firmware(FOTA) of nrf5340 using AT Command of nrf9160.
I've already reviewed the content in the dev academy below https://academy.nordicsemi...
Hi,
I'm using nrf9160 MQTT at commands to send real-time data to the cloud. I run into the issue where the MQTT publish may fail (frequency varies around 1 out of 500 publishes...
Generally, the peripheral calls the sd_power_system_off() function to enter power off mode. Then use GPIO interrupt to exit the power off mode and connect to the central device...
Hello,
I've been encountering build issues when trying to include MCUboot as a bootloader for my nRF7002DK project using the Nordic Connect SDK version 2.5.2. Specifically...
Hii,
I am using NFC tag reader to interfacing with nrf52832 board , I am using nrf connect 2.6.0v. The sample file is also given( TAG_READER )
I am using spi protocol...
Hello,
Our setup consists of two nrf52840 devices on custom boards. The devices establish a BLE connection via the Coded PHY (S=8). DLE is used. Connection event time is...
