Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I have developed a Zigbee application using the nrf52840 DK board + nRF Connect + Zephyr and it is working. Now I am trying to move that app over to the nrf52840 dongle. It...
Hi, I am using nRF52832 development board and I have a motor driver. Motor driver has external power supply, I am just using nRF52832 to set directions which consumes low...
Hello, I am trying to use the dfu library to update the nrf52840 with a firmware stored in a littlefs file in an external qspi flash. I can successfully read the entire firmware...
Dear Nordic team,
it is very important for the RF and the HW engineers to be able to know the current transmit power of the modem. That will help us evaluate the network...
Hi
I'm looking for an example implementaion code on the nRF52840 without an operating system. Is there some example or application note?
I connected the SPI and all IO...
Hi,
I updated to VS Code V1.65 today and had some strange behavior with the NRF connect extension for VS Code.
After updating, clicking any "Action" in the sidebar (e...
I have already implemented DFU update in our one product. Which have fast USB interface and fast "lag-less" UART interface to nRF chip which is used as our bluetooth central...
I am using a code based on nrf52-ble-app-uart-c-multilink ( https://github.com/NordicPlayground/nrf52-ble-app-uart-c-multilink )
If the central is working and the peripherals...
Board: NRF52833 (PCA10100)
SDK version: 17.0.2
Softdevice: S122
I am trying to perform USB DFU for my application. As I am using nrf52833 board, there is no available...
Hi ,
SDK 17.1.0
SD132
SoC - nrf52832
I am following the below given link to create custom service.
https://github.com/bjornspockeli/custom_ble_service_example...
We plan to use it with the Converter mode enabled for low current consumption.
However, if PIN is always set to Hi in order to use the Converter mode, about 300μA will...
After a lot of thought about the issues with TCP under EDRX or PSM , I have a feature request.
I would like if the application layer could know when a TCP socket was sitting...
Hi Nordic team
I tried ncs 1.9.0 peripheral_uart sample (\TOOLCHAIN\v1.9.0\nrf\samples\bluetooth\peripheral_uart) at PCA10095 v1.0.0 DK.
1. Application core: Board is...
