I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I tested "ble_app_buttonless_dfu" example and "ble_app_beacon" example. Everything was fine. Now, I am trying to make an application that advertise as a beacon and supports...
Im trying to come up with a commercial low power sensor module using the nRF91 DK. What happens if i use my own Telstra SIM card, will it have access to NB-IOT in South Australia...
I use Android nRF Toolbox Uart and NRF52832（SDK version ：17.0.2，app：ble_app_uart）。
I set （RX＆TX）PHY 2M，（11.25-15,0,20S）。
form NRF52832 send data to Android nRF Toolbox...
Hi guys
I try to develope a bluetooth application with a customboard on Zephyr 2.4. At the moment the firmware should work on the nrf5340-pdk until the hardware is ready...
Hello NordicSemi,
We are developping a product based on the nRF52840-QIAA and are using the schematic reference nRF52840 DK Hardware files which is similar to the circuit...
I have developped an application using bluetooth mesh with NFC to read a text record. I am currently using the nRF52840 DK Rev 2.0.1 2020.11.
Regarding my software setup...
W e have the problem with GPS that it sometimes takes a long time after a cold start until the modem gets a fix. I see strongly fluctuating times between 78 s and> 600 s ...
I'm trying to modify the asset tracker for the Thingy91 to read the actual values of the ADXL362 and BME680 sensors. By default for some reason the project uses simulated...
Hi,
this project is upgraded from 51422, now use 52832, sdk 15.3 and sd332, we encounterd a issue that the ant burst always fail after first segment is sent while ble is...
Dear Nordic:
Help to see this problem，tks
Problem description:
SDK：nRF5_SDK_15.2.0_9412b96
status：bonded device
demo：Let's refer to this sample code ---- nRF5_SDK_15...
Hello, all.
I am working on a project in which the ultimate goal is to read an 8-bit signal with 10kHz frequency.
To test if this would be possible, I tried to generate...
I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as controller.
The problem currently i am facing is to send a init packet to my nrf board...
I'm running a fine working example based on the Bluetooth low energy Characteristics, a beginner's tutorial on the nRF52DK using SDK 15.3 working as a BLE peripheral.
When...
Hi,
we have developed a nRF52 based product using SDK 14.2 + S332 5.0.0. The product is self-controlled by a Ionic-Cordova App (Android and iOS).
Unfortunately, late in...
