Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
Hi, I am using the nRF5_SDK_14.0.0_3bcc1f7 with SD v5.0.0 and the ble_app_beacon example together with the Jlink Monitor mode for debugging. The issue is that under some circumstances...
Hi,
I m using now two thingy and I m looking for the possibility to compute the difference between the two accelerometer to determinate the the moment of one compared to...
I'm trying to get back into the swing of bluetooth development, and right now I'm trying to find an overall ladder/timing diagram for a full bluetooth/softdevice transaction...
Is model Publish Retransmit (Mesh Spec 4.2.2.6 and 4.2.2.7) currently implemented in the Mesh SDK? I noticed that with Publish Retransmit Count set to 1, the Zephyr Mesh stack...
In nrf52832 datasheet, it uses" 64 MHz crystal oscillator, using external 32 MHz crystal "
then, can I use external 16 MHz crystal or external 4 MHz crystal to drive nrf52832...
I couldn't find nrf_drv_timer.c file. I want to create timer so I try to different SDK for my work. I am using SEGGER IDE for prepare software but i encountered lots of problems...
Dear nordic,
I try to build BLE application everything works fine expect the UART. The UART has transmission issue.
it has no problem in receiving. but when i tried...
Hi,
I am using nrfMesh2.2 SDK. I want to add models other than GenericOnOff and configurationclient to the interactive_pyaci. How do we proceed with this?
I found the utility to create the binary image of the production data for my Zigbee device but cannot find any documentation on how to incorporate the generated BIN file into...
Hi,
I have a custom board with nRF52832 and I'm using SDK 13.1 and softdevice s132 4.0.5. I have a GPRS module that I will use to receive the new firmware image and I will...
Dear Nordic,
I installed nrfConnect 2.6.1 and lauched "BluetoothLow Energy" application. Then i selected my board and it asked "Device must be programmed ..." and loaded...
Hi There,
I'm interested to customize the eddystone TLM parameters as per the image below, which is replace the Battery voltage with Button detection On/Off.
I did...
I was able to successfully make the BLE Peripheral Eddystone Beacon Application in "nRF5_SDK_12.3.0_d7731ad" in Windows 7 32-bit (pca10040), using GNU Tools ARM Embedded version...
Greetings,
I'm fairly new to developing with Nordic ICs using the SDK, I have previously developed for some nRF51x MCUs using some modules that had an Arduino library...
