I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
Hello,
I'm using a custom board (nRF51822 QFACA chip), with the optional 32KHz crystal.
When, I use the SDK 5.1.0 and the S120, my code works perfectly. But when I try...
I would like to develop some BLE applications using the nRF52 Preview DK, that embed a NRF52 revision AA. S132 soft device 2.0.0-8.alpha documentation says that is not compatible...
I've been developing some ble code for a custom board. Recently, I just finished creating a new smaller board. When I load my code onto it, I notice that I have trouble discovering...
Can the nRF52 be programmed by 6-pin J-Link Adapter by just connecting the following 4 pins,
Pin 1 : 3.3v Supply,
Pin 2 SWDIO,
Pin 4 SWDCLK,
Pin 5 GND,
Can pins 3...
I want to save custom data in NV address. Which address is safe to save custom data in NV?
I'm working on nRF51822-xxAC with very simple and small code.
And, using s110...
My project for nRFs has a few configurations for different boards.
So, how to enable 'batch build' button to build all configurations by one click? Currently this in disabled...
code.c
ui_flash.c
ui_flash.h
Hi guys,
So we are building the Ibeacon project , and faced with some problem:
The chips falls hard reset periodically when trying...
Hello,
Is there any todo list about how to protect an application from hacker unsollicited copies to avoid illegal clones ?
how to allow jtag in write only (disable...
Hi all,
For PAN 42 which describes an issue write to RAM after a POR. When was this issue fixed? I can't seem to find out what versions of Silicon are subject to this issue...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
Hi All,
I'm facing unstability in connecting my Central BLE device based on bluez to connect to Nordic Uart service based device.
For every 10th or 11th connection ...
When I use a power supply, (3.0Volts-60mA limitation) with the DevKit boards nRF51 or nRF52 the input voltage is clamped at around 2.0 V and the current is 60mA : the SoC...
Hello, kindly any one tell me how to run a beacon code in nordic Ev kit . I've been trying to make it work . What type of changes i need to do in the code .
Hi,
I want to migrate my firmware from nRF51422 and softdevice S310 to nRF52 and softdevice S332.
Please share migrating step if anyone knows.
For nRF52 and Stack S332...
