In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi
My device and Software details are as below
nRF52840 EVK
Softdevice:s140
SDK v16
I am new to BT and USB protocols.
As part of our POC I eed to test and establish...
Hi,
I have implemented a set of custom mesh models on nCS. In vendor models we have reset handlers, as in nrf documentation: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
We cant get a connection to our Matter Development Board like in the discription: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/connected-home-over...
This may just be more of a Zephyr question but wondering if anyone in the Nordic community has experience with this.
I'd like to generate code coverage reports when running...
Hi,
I'm developing a board based on the thingy91 (same nordic silicon, different sensors) and using nrf SDK v2.0.0
The blinky application is flashed and run correctly...
Hello, I am using the nRF connect SDK and am currently running into some issues with using the on board ADC. My issue relates to the adc_channel_setup function which returns...
Hello,
I am using an nRF52833 dev kit and the Zigbee light_switch example from nRF Connect SDK.
I was trying to implement the sleep mode so I wanted to estimate the power...
Hello,
I am having an issue with board bring up for a custom board I developed using the nrf5340 processor.
I have created firmware based off the peripheral_uart sample...
Dear Nordic support team,
I bought 3 piece of nRF52-DK from MOUSER, 1 piece of nRF52-DK version is 2.1.0 , and another 2 piece version is 3.0.0.
nRF52-DK version 2.1...
Hi there,
We're using nRF52840, IAR 8.40.1, nRF5_SDK_16.0.0_98a08e2. My question is, I need to toggle a GPIO pin right after SPI finishes the TX transaction and right before...
I am trying to use both USB and BLE on an NRF52840 using SDK 15. It hit a hard fault during initialization, specifically when it tries to enable the USBD IRQ.
It looks like...
I am familiar with the PTCRB certification process for an IoT device incorporating a certified module. https://www.ptcrb.com/wp-content/uploads/2020/08/10_Steps_to_PTCRB_Cert_for_Cell_Enabled_IoT_Devices...
Hi, all
How to enable and set fast advertising and slow advertising in NCS.
We always set advertising parameters in legacy SDK like below, how to implement it when using...
Hello All,
Thank you for reading my post. I have finished developing a small battery powered device I have been working on and just completed programming the functionality...
