Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hi,
Nordic nRF Connect SDK includes also the Zephyr repository with a number of examples. I am interested in the HCI UART example in Zephyr, and I want to open from Nordic...
Hi,
I am currently working on a project similar to this thread:
However, the thread stop updating. I followed what Einar suggested, to merge the Decawave example code...
Hi all,
I have an issue on my device. We have implement OTA update but sometimes, the nfr stucks on DFU mode after the update. Even if the update is succesfull.
We use...
Hi All.
I am checking battery autonomy with different settings in my Module (with an nRF52840 SoC inside) since, in my project, this is a critical restraint. I am feeding...
now, I need transfer data between nrf52840 (base on zephyr OS) and python app through PYSERIAL. Is it possible to use something like RTT or shell_uart to transmit/receive...
How do I switch between being SPIS/SPIM with the Zephyr library?
I am using ncs v1.9.1. I have code that works separately as a slave or master but I need to make it dynamic...
I want to use +8 dBm TX power so I added CONFIG_BT_CTLR_TX_PWR_PLUS_8 to my prj.conf, and then realised it doesn't do anything.
I then found set_tx_power() on these pages...
The problem: We are getting a hard fault immediately after jumping from the bootloader while trying to initialize the nRF USBD driver. The fault happens in nrfx_power_init...
Hi,
We are trying to integrate a remote controller functionality for smart TV and set-top box etc, using our product based on nRF52832(nRF5 SDK). I understand that we can...
I am trying to use a SPI bus with three MAX3109 chips attached to give me 6 UARTS. My overlay is defined as follows:
& spi1 {
cs-gpios = <& gpio1 13 GPIO_ACTIVE_LOW...
Hello, I'm working on a s332 application and I need to include the DFU feature in the code. I've managed to perform a DFU on s132 applications following examples like this...
I've built and able to the run the 802.15.4 RF Phy Tester but it doesn't seen to recognize any of the custom commands. Can you provide more insight into this please?
Please ignore Product Type I selected - i set it to just select that to something.
I'm planning/designing a comm box, which needs to speak to ZigBee based nodes/sensors...
Hello
I'm a beginner. I am using NRF52 series and coding in segger embedded studio. I have modified the ble_uart example and added some extra code so that I get the sensors...
