I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
I am using a QFN73 pin package of nRF52840. The data sheet says it has built in balun. So if I follow the reference circuit, where do I see 50 ohm looking int to the chip...
having just seen the announcment about the bare-metal SDK, i gave it a try using my "hello world" of BLE -- a minimal beacon app which i actually use to benchmark BLE platforms...
Hi
I am capturing a digital signal with the nRF PowerProfiler Kit II from my board that can either be 12Hz or 2kHz depending on the state of my application.
In the below...
I am using an nrf52833 with MCU boot. In an abnormal situation, the Vcc hoovers around the BOD threshold of 1.6V-1.7V. The Vcc in this situation is noisy (with 100/150mv swings...
Hi,
I have been making a sequential channel sounding program. I tried very hard to get rid of memory leaks and now the program is able to sequentially range with three reflectors...
Hi,
I am in progress of making own audio application. I wanted to try 8_2 configuration. I see however, that despite that, 10ms window worth of data at that sample rate...
Hello. Earlier we had nordicplayground/nrfconnect-sdk docker images for v2 (e.g. nordicplayground/nrfconnect-sdk:v2.9-branch ). But it seems there is no docker image such...
I have the revision 1.0.0 of the nRF54L15-DK. I want to use the SPI pins on the GPIO header P2. The datasheet says: nRF Connect for Desktop's Board Configurator application...
Hello,
After updating to the latest version of nRF Connect for VS Code, I encountered an error.
I am no longer able to erase, recover, or reset a board from within VS...
Hi,
we develop a battery powered device that has a battery charger ic. Can the ppk 2 measure negative currents in ampere mode when the battery is charged?
Hi all,
I have Nrf52 devices that use Nrf DFU with "Buttonless Secure DFU Service".
I would like to integrated the ability do to firmware update the devices to our "fleet...
For the nRF54L15, what is the voltage at the output pin of DCC (and input pins of DECD, DECA, and DECRF) in DC-DC mode?
Is it 0.9V? Is it constant?
Vinson
Hi,
We are using both nRF54L15 and nRF54L10 in our product, with DFU support where an external flash is used as the secondary partition on both MCUs. The hardware connections...
Dear Sir,
I am getting the below Error During building of LED Blink Program for nRF52840 Module using PCA10056. Below code I am Trying to run:
#include <stdbool.h> #include...
