I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello, just beginning initial investigation into nRF9151. Project requires communication to several I2C-based sensors and transmit data directly to cloud via LTE, using the...
Hi,
1) I want to collect sensor data using BLE like the following topology, the sensor devices are battery-powered, which sample in the NCS is suitable to modify?
2...
Hey guys, for testing purposes on nrf52833 and SDK 2.8.0 I want to use a simulation and stumbled upon bsim . I followed the instructions there and can build and run the hello...
I encounter this problem:
The radio_test application works correctly on the official nrf52840dk board, but cannot receive input commands on my custom product board.
However...
Hi,
I have been developing a PCB with an nRF9151 and a SKY65943-11 LNA among other ICs. I looked up the nRF9151 Development Kit (PCA10171) datasheet for some of the pinouts...
I am running a modified asset_tracker_v2 on a nRF9160. all is working fine. I am upgrading from SDK v2.5 to SDK 2.90. After a build I find the merged.hex file under the build...
Hi everyone,
I've purchased two nRF905 modules ( www.otronic.nl/.../nrf905se-draadloze-transceiver-met-antenne.html) . I want to establish communication between a Raspberry...
we used SDK V2.6.2,
we used external flash for the OTA,
when we do the OTA after the NVS flash is erase so how we can solve this,
we used nvs_storage for this,
EMPTY_0...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
I am using a customized PCB (nrf52840) and I have been successfully set up the SPI communication in between the nrf and lsm6dso
I used 0.11 as clk , 0.27 as MISO and 0.25...
Hello. We are testing nrf5340 - nrf7002 using the example of blpovisioning. I try to put on/off function using button, but if I reset pcb and turn on, it will connect to wifi...
I have our app on the nRF7002-DK board running with MCUboot configured for USB firmware updates. That is working fine, but is there some way to enable the console output from...
Hello.
I have been successfully flashing the nrf52840 dongle using the nrfjprog comand. I have been successfully able to reset and erase as well. Recently however, none...
I'm facing issues with my brand new PPK2 tool What I've done so far, my setup : * Ubuntu, linux * I installed latest nrf connect application from official * Installed Power...
Hello,
I've been using nRF54L15-DK devboard (0.9.2 revision on the label) for about a month now without any problems until today.
I wanted to change VDD output voltage...
