I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi,
I am new to DevZone as well as BLE development itself. I am currently working on a project and trying to undestand the IDE as well as the processes and workflow of the...
Hello Community & Nordic support, Observed behaviour: my project build with nRF Connect SDk v2.1.1 was with errors
expected behaviour: my project build with nRF Connect...
Hi,
If I run my nRF5340 peripheral BLE NUS service with NCS 1.9.2, I get two different behavior at console.
When I connect from my WIndows PC running nRF Connect for Desktop...
I'm not sure if this code I inherited is using k_poll_signal correctly because it seems like I can handle it in a much simpler way with an atomic variable.
The below code...
I want to use the lsm6dsox IMU on my Adafruit feather nrf52840 sense board, and I should use other I2C, other than p012 and p011, to not have a problem with the other IMU...
Dear team,
I am not able to flash the nrf5340 audio application (gateway) to the nrf5340 Audio DK using SWD from nrf5340 DK. I nrf5340 DK outputs 1V8 logic.
I can see...
I am using S132 in the Segger IDE on an nrf52832.
I am using SDK version 17.0.0_9d13099.
When I call sd_ble_gatts_hvx() from within a GPIOE ISR (externally pin triggered...
Hello,
Looking to see if there is a pinout TABLE for this package. I've seen the schematic drawing already but looking for a table format which is more user-friendly when...
I've set "NRF_SDH_BLE_GAP_DATA_LENGTH" value to 27 on peripheral side, and it've changed to 251 after connection. On the central side, the value is fixed as 27. I believe...
Hello,
We're currently developing PCB with nRF5340_CLAA SoC. For specific reasons, main supply voltage was changed from stable 3.3V to 3.5V that comes from DC/DC converter...
I recently followed the instructions laid out in the "nRF Sniffer for Bluetooth LE" User Guide version 4.0.0 and having trouble seeing the nRF Sniffer interface in Wireshark...
Hi,
I am trying to implement bluetooth uart peripheral for nrf52811. I try to learn the code from example and want to check the result on my board.
When I build the...
Hi,
I'm on NCS 1.9.2, and I'm having a unexpected behavior on the consumer thread of a k_fifo. The documentation states that the k_fifo_get routine removes a data item from...
Hi all.
I was planning to build ble example and combining it with I2C, but I found this error
I check several previous posts on this forum before and solution...
Dear Nordic,
I am a beginner. I would like to transmitt the sensor data from a Lora32u4 board (End-node) to an nRF9160 Thing Plus (As a gateway) connecting to Lora SX1276...
