Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi
I am using FOTA DOWNLOAD to update device's application firmware. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/libraries/networking/fota_download.html...
my net core only output the boot information and i enable config_log that uart console will put some strange info
CONFIG_LOG_DEFAULT_LEVEL=3
appcore output to ttyACM1...
Hi
I could not really find a satisfactory answer to my question, what (if any) impact has the setting of the SLEEPDEEEP bit before calling nrf_pwr_mgmt_run? I'm wondering...
How does the slm routine of ncs1.9.1 use rtt log. Below is my configuration:
With the default configuration, there should be RTT log output, but nothing happens in the...
Dear Nordic Engineers
If we use the NFC Tag of nRF52 series chip.A re there any card readers on the market that can read or write?
Such as ， NXP's NFC tag chip can be...
Hi Nordic,
I am using nRf52833-DK with zephry, an now I'm tring to drive ws2812 led strip.
I notice that there is no nRf52833-DK example in zephyr/samples/drivers/led_ws2812...
Hello,
At the following URL,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support.html
In "The Thread and Zigbee protocols support...
Good Morning people. I'm developing a module with the soic nrf52832 and I'm having doubts about the electrical schematic of the UART communication with another MCU. I analyzed...
Hi
In the old SDK I was able to put manufacturing data into the scan response package using:
ble_advertising_init_t init; ble_advdata_manuf_data_t manuf_data;
and just...
I am migrating to ESB from Gazell to take advantage of the static 252 byte sized payloads. However, there are two things that are very different that I would like to figure...
Hello all,
looking at how to navigate with the nRF tools, hardware amd software.
For example, have designed a bit of applciation with seome peripheral drivers, but I am...
Hello,
I am having trouble communicating with the nRF82532 and the DTM software. I am using nRF5_SDK_17.1.0 which has the DTM firmware. The project that I selected is: direct_test_mode_pca10040...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
