How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I am working on a project using the nRF5340. I will eventually be supporting OTA DFU for both cores so I need to be able to statically define the partitions for both...
Hello, I am porting to nRF5340 from nRF52833. Previously, we were using sdk17.0.2 for nRF52833 and we were able to successfully implement encryption algorithm AES-CTR-128...
Hi,
I have a NRF52840-DK (400236). I was using it for the development. It was working perfectly.
Suddenly the issue arises the power section is heating up.
I am powering...
Hi,
I am running the standard Grove LCD code, as below but am getting an error, " Grove LCD: Device not ready.'
the code is
my overlay file is
and my proj...
Hello,
we have a set of router devices already on the market: each of them was developed using 4.0 stack.
now we're aligning the stack to the 4.2 version observing a very...
Hi!
I've followed the app timer example to implement app timers in my project. My project is low power consumption oriented. When I use a repeated timer, power consumption...
Hello,
We are integrating the nordic sdk for DFU on our own application on Android and iOS.
We need to know al the possible error codes that the sdk can sent but we...
Hi DevZone,'
I am trying to use the crypto library with CC310 backend on a FreeRTOS application using the nRF52840DK.
My problem seems to be that when initializing the...
Hello,
I am trying to set the default TX power to +8dbm for all stages of the BLE transmission process, including when advertising is active. I have referenced the "hci_pwr_ctrl...
Hi,
My project is set up as out-of-tree using NCS v2.0.0. I would like to restrict the NCS version such that it will throw a compile-time error if a non-matching version...
I am using SDK v16.0.0 with s140 softdevice. In app_util.h, there is STATIC_ASSERT_SIMPLE and STATIC_ASSERT_MSG definition decided by platform like __CC_ARM or __GNUC__. ...
Dear Nordic fellows,
I have a NRF52832 and I want to configure the UARTE peripheral driver in not blocking mode. I want to try and exploit the double buffered DMA. I'm using...
I am using UART to try to send and receive data from the MCU on my nRF9160 board. I noticed in the tutorial on DevAcademy that using the asynchrounous mode, we're able to...
Hi！
Due to product requirements, I need to make the broadcast package contain 128-bit UUID so that the APP of our company can identify the device. The chips of other manufacturers...
