How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hi, I’m trying to generate a PWM signal directly using the nRF5340’s PWM peripheral registers (not using Zephyr’s pwm_dt_spec or driver API).
The LED turns ON correctly...
Hello,
I am trying to adapt the "Interfacing with a sensor over SPI" example from the nRF Connect SDK Intermediate Dev Academy course in Lesson 5. When I run the code as...
Since it was brought up in the Webinar today, that the nRF54LM20A is not recommended for use with LE Audio due to the lack of an Audio PLL, I was wondering that the Audio...
Hi Nordic Dev,
We are experiencing issues with sudden connectivity loss and hardlocked devices 1,5 years after product launch. We are currently suspecting the flash storage...
Hello,
I have a Thingy:91x.
I flashed a BLE central program to the nRF5340 on this device.
However, I get an error initializing BLE. I've confirmed that this program...
Board/Setup:
Board: nRF9151 DK / nRF9151 SoC
Peripheral: External BLE module connected via UART1
Use case: BLE module is only needed during commissioning...
Hi there,
I have been trying to implement a low-power mode that basically suspends UART, I2C, etc before entering sys_poweroff() when critical battery level is triggered...
Hi,
I have several field devices using the LTE Link Controller library with nRF Connect SDK v2.5.1. Most of them work fine — they are programed to connect every hour. However...
Greeting Nordic Expert !
I would like to override the following hook in MCUboot:
int boot_perform_update_hook(int img_index, struct image_header *img_head, const struct...
Hello,
In the nRF52840 Product Specification PDF v1.11, on page 836, the second paragraph down states:
" The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and...
Hello Nordic team,
I’m using the nPM1300 development board to charge a 950 mAh Li-ion battery , and I’ve configured the charger as follows:
Charge current: 800 mA...
Hi,
I'm unable to get the PPKII kit to "connect" to my PC. After selecting the device it just says "Connecting..." forever. Some notes: - When first connecting the kit...
Hello,
I am trying to write a python script that performs a DFU on a nRF52840 so I can change its firmware without pressing any button. I think I have to use the pyusb...
Hello everyone,
I’m currently planning to develop an application that involves multiple Bluetooth devices operating within a certain range outdoors. Since there’s no option...
