Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Hello,
I would like to know if the application / use case stated below is implementable.
In my application I would like an nrf52840 to communicate with the Bluetooth module...
hi,
In the NUS routine, it is necessary to turn off the peripherals before entering the idle mode to minimize the power consumption, but there is no change after adding...
Hi,
I'm trying the sample fat_fs on the nRF5340 DK
1) It does build, but there is awarning
CMake Warning at D:\nRfConnect\v1.8.0\zephyr\CMakeLists.txt:722 (message)...
On a MCU PCA10040 v2.0.0, I ran the command:
.\nrfjprog.exe -f NRF52 --program .\final_image.hex --verify --reset
Which subsequently caused the board to go into a reset...
I have a Thread bench-top environment set up that includes
One nrf5340dk flashed with the openthread coap_server firmware build and flashed on 1.8 via Visual Code
Two...
Hi
If a bug stop the application to feed the wdt,Is there any way to store 8bytes application data to flash before reset which occurred by wdt?
I find that there is only...
Hi,
I'm having some difficulties understanding how to manage commands in endpoint-specific callbacks. For example, when receiving a "ZB_ZCL_CMD_CONFIG_REPORT" I'm able to...
Hello,
I have a peripheral (nRF51822, S130, using the peer manager) that should be paired/bonded with one or many centrals. I have followed the example ble_app_bms from...
Hi everyone,
I implement nrf5_SDK_17.0.2 ble_app_uart example and I use an android app like nRF_Connect to receive the uart data on my cell phone.
The problem is that...
Hello,
I am having an issue with the nrf_libuarte_async librairie.
I am sending data via nrf_libuarte_async_tx and receiving the data properly via the IRQ handler...
Hello all, I am currently trying to get the nrf sniffer into the hardware of my nRF52840 DK board. Unfortunately when I call the programmer via the nRF Connect Desktop APP...
Hi, I am working on ble_app_uart_pca10056_s140 and after 3 minutes and I am getting the following error.
When I change APP_ADV_DURATION to 0 also get the following error...
Hi,
We have a product based on nrf52840 which is already in production for several years. It was built over SoftDevice132 and SDK 12.3.
The project has 2 components: ...
SD140
nrf52833, custom application based BLE Central Uart Project.
We would like to try the UART DMA functions available in Soft DEvice, s140_nrf52_7.2.0.
I have not...
