Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Dear Member,
I want to add ADC the main code,
but I got :
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_ppi_init (referred from adc.o).
I'm using...
Hi, I am not sure whether there is I2C pins on nRF52840 Dongle board as based on the Adafruit Feather nRF52840 Express the pin is P0.11 and P0.12 as shown below: SCL 0.11...
Hello I am learning how to connect timers with gpio via PPI, i working on nrf52832dk.
So far I have connected the RTC 0 alarm channel to the LED no.3 (pin no.19) and its...
Hi, I am Shuang. I am now working on the Bluetooth direction finding function, but I have some problems, and I hope I can get your help.
I have experimented with Bluetooth...
I know Thingy:52-FW project has been marked as deprecated. https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
However, I'm trying to get the development environment...
Hi，
I am using the ZBOSS SDK to develop the zigbee function, and I see that there are
TRACE_MSG(TRACE_ZCL1, ">> zb_zcl_finish_and_send_packet_common param %hd delay %d...
Hi,
based on my previous post/question here and after I managed to cconnect 5 specific address devices/peripherals from my central (DK) based on filtering (solution in the...
When I want to add LTE to my project I've done this by adding
to prj.conf. When I (pristine)build (within VScode, and when using the command line) i get the following...
Hi guys,
I am using the nRF52840 until recently - with the 2t2 library from nrfx - on a Zephyr application over the latest NCS 1.7.1
I wanted to add tag write capabilities...
Hi there
prj.conf
EXR-200-004.dts
main.c
Please refer the .dts custom board file. We took a basic file generated from nRFConnect for nRF52811, and added in some missing...
Hello,
In nRF Connect desktop application, under Bluetooth Low Energy tool v3.0.0, whenever I connect a peripheral device using this application, I see the option to update...
Hi
my application is driving a RGB LED by one wire, this is request a higher sequence , when you drive the RGB LED ,this task can not be interrupt , I am use timer3 to...
Hi all,
I'm working on a project using the nrf52832 with SDK 15.3.0. Our device is battery powered and in peripheral mode. When a central connects it sends +- 300 bytes...
Hello,
I have the Icarus IoT board nrf9160, and I'm trying to connect it to the nrf connect for desktop but it doesn't seem to support the board. I'm getting the following...
