hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hello DevZone,
I'm developing a HomeKit project for the customer. They require 2 BLE advertising in one device. One advertising is for HomeKit over BLE, and the other one...
i want to switch between two code... the code is simple led blinking i am trying for the testing purpose...in my code 1 led1 is blinking 500 ms of delay and in my code 2 led2...
So from my understanding from the zephyr documentation, if I want to use 7 bit I2C addressing, don't set I2C_ADDR_10_BITS. I am wondering how I can make sure this macro is...
Hi,
How do I add the System ID characteristic (UUID 0x2A23) from the Device Information Service (DIS) using Kconfig commands in the prj.conf file?
For example, I can add...
Hello,
I am having a strange problem with nRF Connect SDK for VS Code, and would appreciate some help.
I don't know what I did, but suddenly I am not able to "Generate...
I am developing a product that uses the chip of NRF52832 and runs FreeRTOS on the chip to manage my task list. However, I found that the program would be stuck in the idle...
I've got a custom board that uses an nRF52832. Firmware was built with NCS v2.6.1.
My hardware uses a MIC826 IC for ensuring the nRF52 is held in reset whenever the power...
I'm looking for a beginner's guide to setting up external flash on the nRF9161 DK. I saw nRF Cloud Multi-service as an example, but its docs did not explain what was needed...
Hello,
I have had posted several times over the years and solved a problem or two. I find it very thorough to finish out a post by concluding my findings. This said, I...
Hello everyone,
My problem is that I could not flash one of my NRF5340 Audio DK boards, the program that is installed before was headset configuration right. I am using...
We wanted to share our feedback as we recently went through Zigbee 3.0.1 BDB/cluster certification using the ZBOSS with our end device product. While we were ultimately able...
I just got a new set of nRF5340 Audio DKs and I may have been too fast on the trigger trying to flash the boards with example programs. I'm using VS Code, and I'm a newbie...
I want to know where did the "desired_data_size" value in le_audio_rx_data_handler come from?
And why "data_size != desired_data_size" means the pkt is bad frame?
Thank...
Hi,
We have recently acquired a new firmware engineer, and would like to get him set up with a development environment for developing code for our product. The problem...
Code running on nRF52833 devkit version 1.0.0 that continuously sends an empty 500 kbit/s radio packet:
Code running on nRF54L15 devkit version 0.8.1 with chip revision...
