Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello support
I have modified the cli examples and run into "undefined reference to `nrf_cli_uart_transport_api'" linker error.
The error message is
Compiling file:...
Here's my setup:
1. RPI4+nRF52840 dongle as OT border router
2. nRF5340DK running CoAP client example application
3. Wireshark running on Mac OS, with nRF52840 dongle...
Hello!
I'm trying to develop a mesh network and I've been building on top of sensor example, which has been very useful since I'm reading a few sensors. However I want to...
I am trying to generate ECC key pairs using MbedTLS on Connect SDK.
I found this code block on stackoverflow and validated from mbedtls/programs.
"mbedtls_ctr_drbg_seed...
I was trying to evluate the Periperhral ISO server, however with a NR52dk, but it returns ENOTSUP.
Bluetooth initialized Unable to register ISO server (err -134) [00...
Hi all
I am developing a proprietary radio protocol application using the nRF52805. I am not using a softdevice. Instead, this is all done by accessing the radio registers...
I have seen this question answered for the old Nordic SDK but have not been able to find a solution in Zephyr & NCS. I'm following this post on how to develop a custom BLE...
Hello,
i am using nrf52832 dev kit want to send the nrf calendar parameter through nrf connect app and send through app successfully by taking uint8_t datatype .I have receive...
Hello.
I am trying to write code to read data using saadc and write the sampled data in a micro SD card using fatfs.
I started from the fatfs example and initialized...
I'm attempting to use pc-ble-driver-py on Windows with an NRF52 DK (PCA10040) and running into the error shown below. Using the Heart Rate Collector example, the COM port...
Hi,
I'm using the ble nus uart for my application and I noticed that I was drawing too much current so I went back to the example from the SDK 17.0.2_d674dde which I haven...
I have followed the Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) and was able to comminicate with Azure IoT hub.I have created rootCA and device certificates...
This is my problem description, hope someone can help me. 1. The watch product shipped in mass production is found to be disconnected when using the mobile phone OPPO-k7x...
HI,
i have enabled CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE=y
so after power cycle the device automatically connects with iphone and the service also works fine
after this...
