How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello,
I noticed with the LTE Serial Monitor example code on a custom board with nrf9160 (and also the nrf91dk), the UART interface work initially but sometimes hangs. It...
Hi,
I am working with nRF52833 using the SDK17 Dynamic Pairing example. I was able to expand on it for my use case, and the application is now correctly receiving data...
Hello,
I am using NINA-B406 Custom board which have nRF52833 SOC and using Segger embedded studio with nRF5 SDK v17.0.2 for development.
I want to do the two functions...
Hi, Do you have any documentation at all for the experimental GPS driver? I can't find anything. Google just sends me to a few broken links. Best regards, Jan Erik BikeFi...
Hi, the specification of nRF5 SDK for Mesh v5.0.0. says the interrupt priority has two levels, named priority_lowest and priority_thread.
I am not clear on some things....
After installing nRF Connect for Desktop on macOS, I hit "Install" for Toolchain Manager, and then "Open".
This opens a new window for the Toolchain Manager, which says...
Currently, MQTT is required for nRF Cloud data transmission. We will be using LwM2M as the protocol to send data from our IoT monitoring device to our cloud platform. Does...
Hi, I have a bit strange problems with example project "pwm_library". At first I compiled with segger embedded studio and ran the project on my NRF52-DK board, and it worked...
I have used nRF52811 chip in my custom board.
1. Please provide the First time programming procedure using J-Link (J-Link-Pro tool) interface.
2. We have a nRF52840DK...
Hi teams,
Recently, I upgraded JLink driver to 7.5x and suddenly all of my nRF DK boards are not detected via USB.
All of my 4 DKs shows the same symptom. LED5 near JLink...
I am working on an embedded design that uses the nRF52840 MCU and 2x additional processors (Processor #1, Processor #2).
The intent of the system design requires that Processor...
dear all
I used the lvgl in zephyr. When I made a image rotation, I found that I copied some of the image pictures。Is there anyone in the forum who has encountered similar...
Dear friends: I am based on the following link: devzone.nordicsemi.com/.../device-firmware-update-dfu-with-mcuboot-bootloader Operation steps test the function of mcuboot...
Hello I am using sdk17.0.2 and nrf52840.
I used nrf52832 to combine ble_app_uart and crypto_aes_ctr codes. And now I'm going to move the code to nrf52840.
However, there...
Hi! I made a custom board with an external flash memory that communicate with nRF52840 through QSPI. I have some boards that works very well, but i have someones that freeze...
