Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
We are using a custom board based on nRF54L15 with MCUboot and compressed image DFU over OTA. DFU was working correctly when updating between NCS v3.2.0 and v3.2.4, but after...
Hi everyone,
I need to implement a coded Phy ble communication in a project and for that I wanted to use an nrf52840 dk. However, for it to be able to compete with the Aircable...
Hello Nordic Team,
I am currently working with the nPM1300 EK together with the nRF54L15 platform and a custom 40 mAh Li-Po battery.
I am facing an issue while configuring...
I'm developing software for the nRF5340 based on the NCS 3.2.4 "hello world" example. Adding bt_enable() returns error code -11. Please tell me how to implement bt_enable...
Hello, I am developing a low-power nRF52840 product using the ncs Zephyr environment. Currently, I have suspended peripherals such as UART and I2C, allowing the system to...
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
I've built the softsim external profile from Onomondo and it works. But when I try to incorporate it into the app I'm currently developing, it renders the code unable to boot...
I am trying to enter MCUboot serial recovery mode on an nRF5340 through a UART command.
I mainly followed the Nordic tutorial below:
https://academy.nordicsemi.com/courses...
I'm curious about the approach taken in the nRF Connect SDK's location library for cell neighbor scans ( https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/scan_cellular...
Hello, I am trying to use the latest nrfutil version 8.x.x in my custom project. Previously I had nrfutil version 6.1.7 with `nordicsemi` package included as a dependency...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
I have a nRF9151 dev kit for evaluation that I am following official guide to get up and running using the asset tracker v2 program. I can flash the firmware but I cannot...
I have successfully completed the one script install of Zephyr on RPI and can fully develop Nordic nrf52832/nrf52840. I assume all other supported boards within Zephyr can...
